Hey Bill, thanks for reaching out. I just went out to our warehouse and measured the Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV. The outer tube is 4-1/2" square. The inner tube with the foot is 4".
Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…
Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…
Hey Brandon! Yes, either M-3 transition plate (steel #M368FR or aluminum #M348FR) will do the job, but I’d go aluminum #M348FR since it’s easier to trim and won’t rust if water gets in that recessed area. Just mount it across the lower edge of the…
Hi Marcus! The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver #TA35ZR weighs a hair over 51 pounds. Pretty heavy, but it is a pretty heavy duty wheel. Do you already have a tire picked out for this? It…
Hey Bob! The wall bracket on the MORryde Safe-T-Rail #MR54BR is 2-1/8" wide. Since you have 2-3/4" it will be able to fit in your available space. Are you upgrading your hand rail or did something happen to the original?
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hey Tim! The cable that comes with the Conventional Ramp Door Spring #362SA8207 can be ran over the top. I'm attaching a photo from a review someone sent in that has the cables ran this way for you to check out. Just curious why you're…
I called my contacts at our winch suppliers to see if there were any winches available that perform as you requested. I was unable to find a winch that had an auto shutoff when the winch senses a trailer door is closed since winches constantly feel…
Hey Bob, Based on your description you do have the active shutters on your '24 Jeep Grand Cherokee Overland L. These shutters are between the bumper and the radiator, so since you can see them through the grill that tells me you have them. Since…
I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…
Hey Steven, I was able to find out that the center cap part number you mentioned is for a 3.75 inch diameter wheel pilot hole so for a suitable replacement we carry the #KE95JV which would work great. Did yours break or did they fall off?
Hey Bill, thanks for reaching out. I just went out to our warehouse and measured the Replacement Left/Curb Side Leg for etrailer and Ram Hydraulic Jack #e63VV. The outer tube is 4-1/2" square. The inner tube with the foot is 4".
Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…
Hey Dylan - both M-3 plates measure 81-3/4 inches wide, so you'd need to trim off a little bit. The aluminum one #M348FR would be easier to trim, so I'd pick that over the steel one. The hinge runs the full width so you’ll still get solid…
Hey Brandon! Yes, either M-3 transition plate (steel #M368FR or aluminum #M348FR) will do the job, but I’d go aluminum #M348FR since it’s easier to trim and won’t rust if water gets in that recessed area. Just mount it across the lower edge of the…
Hi Marcus! The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver #TA35ZR weighs a hair over 51 pounds. Pretty heavy, but it is a pretty heavy duty wheel. Do you already have a tire picked out for this? It…
Hey Bob! The wall bracket on the MORryde Safe-T-Rail #MR54BR is 2-1/8" wide. Since you have 2-3/4" it will be able to fit in your available space. Are you upgrading your hand rail or did something happen to the original?
Hey Marty. Caliber lists the weight capacity for their Edge Glide XL Transition Plates item #CA47EJ as matching your trailer's ramp door. So whatever your ramp door capacity is is what transition plates will sport. The 4-pack has a combined…
Hey Tim! The cable that comes with the Conventional Ramp Door Spring #362SA8207 can be ran over the top. I'm attaching a photo from a review someone sent in that has the cables ran this way for you to check out. Just curious why you're…
I called my contacts at our winch suppliers to see if there were any winches available that perform as you requested. I was unable to find a winch that had an auto shutoff when the winch senses a trailer door is closed since winches constantly feel…
Hey Bob, Based on your description you do have the active shutters on your '24 Jeep Grand Cherokee Overland L. These shutters are between the bumper and the radiator, so since you can see them through the grill that tells me you have them. Since…
I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…
Hey Steven, I was able to find out that the center cap part number you mentioned is for a 3.75 inch diameter wheel pilot hole so for a suitable replacement we carry the #KE95JV which would work great. Did yours break or did they fall off?
In these days of customer "no service" I am usually disapointed when doing business with people I don't know. It was refreshing doing business with you. I'm impressed!
Trailer door parts are essential for maintaining the safety and functionality of your trailer. Whether you're hauling horses or heavy equipment, these parts ensure smooth operation and protection. Consider the durability, ease of installation, and compatibility with your trailer when selecting parts.
Trailer door parts, like rubber bumpers, are built to withstand heavy use and harsh conditions. Many find them still in excellent condition after a year of regular use, even under the weight of horses or heavy equipment. They typically need replacement every 8-10 years due to sun exposure.
Most trailer door parts are designed for straightforward installation, though some may require drilling new holes to fit your specific trailer. It's important to check compatibility and be prepared for minor adjustments to ensure a perfect fit.
When selecting trailer door parts, consider the material quality, compatibility with your trailer, and the specific needs of your cargo. High-quality materials ensure longevity, while the right fit prevents issues like chipping or pulling away from the trailer.
Trailer door parts are designed to handle various weather conditions, from rain to intense sun. Rubber bumpers, for instance, maintain their integrity and protect your cargo even after exposure to the elements, making them a reliable choice for any climate.
Common issues include misalignment of pre-drilled holes and the need for additional mounting holes. However, these can be easily resolved with some adjustments. Ensuring the right fit and quality materials can prevent most problems, providing a smooth and secure operation.
Filters
