See what our Experts say about this CURT Heavy Duty Receiver Hitch

• Is There A Trailer Hitch For The 2013 Mercedes-Benz ML350 Bluetec?
  Hello Silvio, thanks for reaching out. The hitches that we offer for the 2013 Mercedes-Benz M-class, the Curt # C13411 and the Draw-Tite # 76141, will only fit gasoline models. Since your ML350 Bluetec is a Diesel, these hitches will not fit. Unfortunately we do not offer anything for the Diesel models at this time. Your only option would be to take a Universal Weld-On hitch like the Curt # 15903 and have a professional welder fabricate something to fit.
  view full answer...
• Trailer Hitch Receiver Options For A 2024 Volvo S60 Plug-In Hybrid
  Hey Paul, There most likely is something in the way that prevents the installation of a trailer hitch on the S models and manufacturers haven't found a workaround yet. That pretty much leaves you with only weld-on adjustable-fit trailer hitches, which would require a bit of DIY to fit. You'll need to measure down from the frame rails to the see how large of the drop you'll need for the receiver tube to stick out from the rear fascia. We offer the following drop sizes: Draw-Tite 7" Drop...
  view full answer...
• Hitch for 1952 Chevy 3100 Pickup Truck
  The only hitch that would work for you is a weld-on such as the Curt # 15903. This is a universal hitch that is a Class V with a 2" receiver and works with frames that are between 18" and 61". I have attached a link to the installation instructions for you to take a look at.
  view full answer...
• What Hitch do You Recommend for My 2012 GMC Savana Utility Van?
  Is the steel step bumper you have installed the factory bumper on your 2012 GMC Savana KUV Van?
  view full answer...
  
• Trailer Hitch Receiver Options For A 2025 Ford E-350 Cutaway Van
  Hey Jim, I drew up a little diagram of the Blue Ox Trailer Hitch Receiver # BLU75UR's dimensions so you can see if this would be a fit. It's not listed as a fit for your E-series cutaway chassis but the F and E-series can some times be interchangeable. It is listed to fit the following models: 2017 - 2025 Ford F-250 Super Duty 2017 - 2025 Ford F-350 Super Duty 2017 - 2025 Ford F-450 Super Duty Pickup There isn't a custom-fit option confirmed to fit so if this doesn't your next option...
  view full answer...
• Recommended Weld On Universal Fit Class 5 Trailer Hitch for BlueBird All American Bus Diesel Pusher
  For your BlueBird School Bus conversion, there isn't a specific confirmed fit Class 5 trailer hitch receiver. The universal fit weld on hitch is your best option. The Class V Universal Weld-on Receiver Hitch # 15903 you asked from is a great option as is the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41991-07. Both of these will have a 2 inch receiver opening. These hitches will need to be welded bare metal to metal for the correct strength....
  view full answer...
• Is There A Front-Mounted Trailer Hitch Receiver For A 2021 Ford Ranger
  Hey Charles, There are no custom-fit front-mounted trailer hitch receivers available for a 2021 Ford Ranger but you can still go with a weld-on adjustable-fit hitch. You'll just need to measure the distance from the frame down to the space between the grill and bumper. We offer the follow drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18" Drop # C99CR
  view full answer...
• Front Mounted Trailer Hitch Receiver Options For A 2019 Nissan Titan Pro 4x
  Hi Kevin, There unfortunately isn't a custom-fit front trailer hitch receiver for your 2019 Nissan Titan Pro 4x so you'd have to go with a universal-fit weld-on trailer hitch like I have listed below. These will all come with a specific drop so you'll want to measure from the frame down to see what size drop you'll need in order to clear the front fascia. These will fit an 18" to 44" wide frame width and any excess can just be trimmed off of the crosstube. Draw-Tite 7" Drop # 41990-07 16"...
  view full answer...
• Trailer Hitch Options For A 2018 Thor Outlaw 37BG On A Ford F-53 Chassis
  Hey Steve, For a 2017 F-53 chassis we currently only have weld-on universal fit style trailer hitches available. Each of these would fit 18" to 44" wide trailer frames and would come with brackets that can give you a different drop depending on your needs. You'll want to measure down from the frame to determine where you want the receiver tube to come out to avoid hitting the fascia. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9"...
  view full answer...
• Trailer Hitch Option For Winnebago Fuse
  Hello Arthur, There isn't anything specifically made for your Winnebago Fuse or Ford Transit chassis, so the only thing you can do is put on a universal weld-on hitch. I recommend taking a look at the Curt # 15903 which gets welded onto frames up to 60 inches wide and provides a drop from the frame of 11-1/2 inches. You'll need to measure to see if that'll work for you, and if not I have added a link below to our entire selection of weld-on hitches.
  view full answer...
• Recommended Front Hitch for a 2012 Chevrolet Express Van
  Hey Lawrence, unfortunately it doesn't look like we have any custom front hitches for a 2012 Chevy Express, but we do have universal hitches like # 15903 that will work but would require you to weld it to your frame. This hitch will work with frames that have a width of 18" to 60" wide, has a max weight capacity of 15,000 lbs, and has a max tongue weight capacity of 1,500 lbs.
  view full answer...
• Can A Hitch Extender Be Used With A Front Mount Trailer Hitch To Park A Travel Trailer
  Hi Don, Hitch extenders place a lot of stress on the hitch because you're leveraging the weight further out so using one typically drops the capacity by 50% when towing. You'd be doing it in a parking lot situation where you wouldn't really be traveling much just more so maneuvering around so realistically that shouldn't affect you but depending on how much weight you're leveraging there could be a breaking point, we just wouldn't be able to know exactly what that point is. The Curt...
  view full answer...
• Front-Mounted Trailer Hitch Options For A 2006 Ram 1500
  Hi Brad, Yes, the Draw-Tite # 65033 sits much lower to clear the air dam, while the Curt Front Mount Trailer Hitch Receiver # 31320 sits higher, requiring you to trim the air dam. These both have a 5,000lb capacity so you should definitely make sure your trailer is under that. If it isn't then you should go with an adjustable-fit weld-on hitch instead to ensure you have the capacity to handle the trailer. You can measure the frame width and measure down to where you have space for the...
  view full answer...
  
• Recommended Trailer Hitch for a 2015 Ford E350 Cutaway
  Hey Noel, we don't have any custom trailer hitches for your 2015 Ford E350 but we do have a universal hitch # C47CR that you can use. This hitch will fit frames 18" to 44", has a class V 2"x2" receiver opening, and has a nice 16,000 lb weight capacity. If you have a wider frame than 44" then you can use # 15903 instead which will fit frames up to 60" wide.
  view full answer...
• Trailer Hitch Receiver Options For A 2024 Fiat 500e
  Hey Jack, There unfortunately isn't a custom-fit option available for the 2024 Fiat 500e yet so the only other option currently would be to go with an adjustable-fit weld-on trailer hitch. To pick out the right one you'll need to measure down from your frame to find how of a drop you'll need for the receiver tube to clear the rear fascia. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2"...
  view full answer...
• Trailer Hitch for a 2005 Chevy Express 3500 with a Knapheide Utility Body
  Hey Jim, thanks for reaching out! Since your 2005 Chevy Express 3500 has the utility body you'll need to look into a more universal hitch like the Curt Class 5 Universal Weld-on Hitch w/ Brackets # 15903. If you didn't have the drop step bumper you might be able to get away with a standard hitch, but in your case you'll need to have a shop modify this hitch to fit your vehicle.
  view full answer...
• Front-Mounted Trailer Hitch Options For A 2024 Toyota Tacoma
  Hi Barry, There unfortunately isn't a custom-fit front-mounted hitch for a 2024 Toyota Tacoma at this time so you'll have to go with a weld-on adjustable-fit hitch instead. This will require you to measure the distance between the frame rails and the also determine how much of a drop you'll need from the frame rails for the receiver tube to come out from the fascia. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865"...
  view full answer...
• Recommended Trailer Hitch for a 2015 Ford E-350 Econoline
  Hey Henry, we don't have any custom hitches for your 2015 Ford E-350 Econoline unfortunately, but we do have universal hitches like the Curt Class 5 Universal Weld-on Hitch w/ Brackets # 15903 which will work the same. This hitch will work with frames that are 18" to 60" wide, has a 15k capacity, and has a 2" receiver opening which makes it compatible with just about everything on the market.
  view full answer...
• Can A Blue Ox Baseplate And Curt Front-Mounted Trailer Hitch Both Be Installed On A 2022 Ram 1500
  Hey Mike, Both the Blue Ox Base Plate Kit # BLU99FR and Curt Front Mount Trailer Hitch Receiver # C87FR would be fighting for the same space on the frame rail where the tow hooks sit so they would not be compatible together. There isn't another custom-fit hitch but you could go with a weld-on adjustable-fit trailer hitch and work with a local fabricator shop to get it sitting right and welded to the frame rails. We offer a few different drop lengths that you can use as a rise or drop...
  view full answer...
• Trailer Hitch Options For A 2017 Thor Freedom Elite 22FE Class C Motorhome
  Hi Cass, There isn't a custom-fit trailer hitch confirmed to fit your E-450 chassis, but we do offer weld-on adjustable-fit trailer hitches that can be used instead. The deciding factor here on what is going to be the best fit is going to depend on how low from the frame the receiver tube will need to be to clear the rear bumper/body of the trailer and any other components that could potentially be in the way. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop #...
  view full answer...
• Trailer Hitch Options For A 1979 Chevy Caprice Wagon
  Hi Carston, The Curt Trailer Hitch Receiver # C12009 is listed as a fit for sedan models only. It looks like we unfortunately don't have a custom-fit option for a wagon model so you'd have to go with a weld-on option instead. To do this you would need to measure your frame width and see how much of a drop you'd need from the frame to clear the rear fascia. We offer the following weld-on options, which will all fit an 18" to 44" wide frame width and any excess can just be trimmed off of...
  view full answer...
• Front And Rear Mounted Trailer Hitches Needed For A 1991 Born Free Motorhome On A Ford E-350 Chassis
  Hey Dale, There unfortunately aren't any trailer hitches confirmed to fit so you would need to go with a weld-on, adjustable-fit trailer hitch and measure from the frame down to the bottom of the fascia to determine how much of a drop you need to clear it. This is going to be the case for both the front and rear hitch. We offer the following drop sizes: Draw-Tite 7" Drop # 41990-07 16" Drop # 41990-16 Curt 3" Drop # 15901 9" Drop # C47CR 10.865" Drop # 15902 11-1/2" Drop # 15903 18"...
  view full answer...
• Trailer Hitch Recommendation for a 2003 Ford F-550 Shuttle Bus Chassis with Rear Steps
  Hey Tommy, thanks for reaching out! Since Shuttle Busses have different frame styles and what's on them, like your steps, adding a hitch will need to be a fabrication project. You'll need to reach out to a local shop to see if they can help you plan out installing an HD hitch like the Curt Class 5 Universal Weld-on Hitch w/ Brackets # 15903, but I unfortunately don't have any more insight into how to do this.
  view full answer...
• Recommended Trailer Hitch for a 2017 Ford E-450
  Hey Steve, we don't have any custom trailer hitches for your 2016 Ford E-450, but we do have a universal option available. Check out the Curt Class 5 Universal Weld-on Hitch w/ Brackets # 15903. This hitch will fit frames from 18" to 60" wide, has universal side weld on brackets, and has a max weight capacity of 15,000 lbs.
  view full answer...