Front And Rear Mounted Trailer Hitches Needed For A 1991 Born Free Motorhome On A Ford E-350 Chassis
Updated 01/27/2026 | Published 08/16/2024
Products Featured in This Question
Question:
Ok, Ive got an oldie. 1991 E350 26foot Born Free motor home. Id want to put a class 3 hitch on the rear for car towing. There has been extensions welded onto the frame to support the rear of the motor home. There are no tanks black,gray or other in between the frame rails. Please advise on the measurement that well need to fit the proper hitch on the rear of this coach. Id like to install a 2inch receiver hitch on the front as well to carry the spare tire or bikes. A Draw Tight 65001 does not work because of the sway arm, would love some help with this as well. Thanx for the tec. support. Dale Plummer
asked by: Dale P
Expert Reply:
Hey Dale,
There unfortunately aren't any trailer hitches confirmed to fit so you would need to go with a weld-on, adjustable-fit trailer hitch and measure from the frame down to the bottom of the fascia to determine how much of a drop you need to clear it. This is going to be the case for both the front and rear hitch. We offer the following drop sizes:
Draw-Tite
7" Drop # 41990-07
16" Drop # 41990-16
Curt
3" Drop # 15901
9" Drop # C47CR
10.865" Drop # 15902
11-1/2" Drop # 15903
18" Drop # C99CR
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- For Towing
- Class III
- 600 lbs TW
- 4000 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Search Results: rv surge protector
- Search Results: trailer hitch
- Search Results: dinette cushion rv dinette table
- Search Results: rv shower curtain
- Search Results: rv shower
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Heaviest Duty Trailer Hitch Recevier for Motorhome on 1999 Ford E-350 Super Duty Chassis
- Q&A: Which Trailer Hitch Fits on a Ford E-350 Van
- Shop: Curt Class V Universal Weld-on Receiver Hitch and Brackets with 10.865" Drop
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: B&B RV Water Center - City/Tank Fill - Ventless - Tank Flush - Shower - 3 Coax - Pump Switch
- Shop: B&B Dual RV Water Inlets - City Water and Gravity Fill - Plastic Check Valve - Black
- Shop: B&B Dual RV Water Inlets - City Water and Gravity Fill - Plastic Check Valve - Polar White
- Shop: Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: How to Choose a Trailer Brake Controller
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Suspension Enhancement
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Brake Controller
- Q&A: Comparing the Curt Hitch C13416 and EcoHitch Hitch 306-X7396 for a 2019 Toyota RAV4
on Trailer Hitch
Jameson C.
1/27/2026
Hey Dale, how did your measurements turn out for the front and rear weld-on hitches on your Born Free motor home? Your results could really help others working with older RV frames and extensions. Sharing what worked might guide someone tackling a similar setup.