Hey Alex. From the information I can find online it does look like your 2011 Keystone Cougar 318SAB does come prepped for a second AC unit. The bedroom roof vent should be reinforced and pre-wired for a 13.5k or 15k BTU unit. To check if your trailer…
Hey Phil! For a tandem axle trailer you will want two of the Leveling Kit with Wheel Chocks for Trailers and RVs #WS28ER. You are correct, one under each tire is best. I use these on my Jayco with one under each tire to keep them off the ground and…
The Replacement Controller and RF Remote for Lippert TV Lift System #LC253395 will not work on your existing RV T.V. lift due to the controller being specific to the motor. The motor, Lippert part 325978; has it's own pigtail that plugs into the…
Hello Herb, It's been a while, thanks for writing in. The short answer is no, the Micro-Air EasyTouch 353 is not currently compatible with the Furrion Chill Cube ducted system like the one included with #FR99TD. The Chill Cube is a newer,…
Welcome back Rich and thanks for the information! To replace your Sharp Carousel microwave R-820BK-F, I recommend the Greystone Built-In RV Convection Microwave item #GR27FR. It measures 21" wide x 11" tall x 15-3/4" deep.…
Hey Jonathan, RV air conditioners all fit a 14" x 14" hole so the only real important factors to determining the correct fit for you would be the BTU rating and whether you have a 6-pin or 9-pin connector. The 936000108 part number you…
Hey Mark, welcome back! Yes, that factory damper will be removed to install the Safe-T-Plus Steering Stabilizer #ST98MR. See the photos below. I also went ahead and linked the instructions and an installation video further down on this page for your…
Hey Skip, welcome back! The Vitrifrigo RV Refrigerator w/ Freezer item #VT56FR is going to need a 12v power supply. You can not plug it into a standard 110v outlet. You'll need to use the PowerMax AC to DC Converter item #PM54VR, which works with…
Hey Nang, the mounting holes on the back of the MORryde TV bracket part #MR85ZR can accommodate bolt sizes that are up to M8 in diameter. M8 is 8mm (about 0.315 inches) across its threads, while 1/4-20 is 0.25 inches. Typically TV hardware is M4, M5,…
In my experience the MORryde Wall Mount #MR82ZR will require additional mounting height to allow it to clear the storage door opening on most RV's. I have had better results using the Mount #MR38DR in the area you are looking to mount the TV.
Hey John, welcome back! I do have a way better functional solution for you. It's the Brandmotion Tailgate Delete Backup Camera with Wiring Harness item #BM67JR. This camera attaches to your license plate bracket. The other end will connect to the…
Hey Jonathan, congrats on the new truck. The 7" drop should be enough, but it is hard to say for sure without knowing what trailer you will be pulling. The 7" drop will get your ball height at 17" or 18" (we measure from the upper…
I like the easy of navigation through the site. It only took me a couple of minutes to place my order. Thank You I will shop this sight again in the future.
Kevin
Manchester, MD
RV TV Mount with Aluminum for wall installs
Mount your screen to a flat vertical surface with an aluminum RV TV mount for a clean, dependable setup. Horizontal use hasn't been tested, so stick to a wall installation and plan cutouts if you want the TV hidden when retracted. Every install differs, and on lift-style designs the TV size can limit the stroke.
No, these are designed for a flat vertical surface or wall. Horizontal use hasn't been tested and may not work as intended. Check the installation orientation in the instructions before planning a sideways slide. If you're trying to hide the TV behind a fireplace or cabinet, verify there's structure to support the weight in the correct orientation.
We do not do custom orders for TV mounts at this time. Choose a system that fits your space and orientation needs as-is. If you need a specific measurement to verify fit, share that dimension so it can be confirmed.
Not all include spec sheets or detailed drawings. If you're tight on space, ask for the exact measurement you need. Measure your available height and depth and confirm clearance for the track and TV. If you want the TV hidden when retracted, plan for cutouts as needed.
The lift's travel is limited by the size of the TV. Mount the track to a flat surface that can support the weight, then verify the TV's mounting hole pattern against the bracket. Check total clearance above and below the TV for full travel, and plan any cutouts if the TV needs to disappear when retracted.
Filters
