Looking For Single Axle Fender For 14" Wheels In Steel Or Aluminum

Question

Question:

Hi Could you tell me if this is available in steel or aluminum ?MFT00320 Single Axle Trailer Fender - Tapered Back - Stainless Steel - 14 Wheels

asked by: Bruce D

0

Expert Reply:

Hey Bruce, thanks for reaching out. Yes, we do have single axle fenders for 14" wheels available in steel and aluminum. There are some slight differences in the dimensions between the different options, but they are all very similar. Take a look at the following:

- Single Axle Trailer Fender for Boat Trailers - Cold Rolled Steel - 14" Wheels - Qty 1 # HP38VR (30" long x 9" wide x 13-1/4" tall)

- Replacement Single Axle Trailer Fender for Boat Mate Trailers - Aluminum - Qty 1 # HP43VR (30" long x 9" wide x 14" tall)

Personally, I'd lean towards the aluminum since it'll have better rust resistance and won't need to be primed or painted. Unless you're planning on painting it to match your trailer, in which case the cold-rolled steel is the best option.

What kind of trailer will you be putting the fenders on?

expert reply by: Jesse M

0

Single Axle Trailer Fender for Boat Trailers - Cold Rolled Steel - 14" Wheels - Qty 1
(click to enlarge)

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Looking For Single Axle Fender For 14" Wheels In Steel Or Aluminum

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching