Hey Leo. The threshold mounting plate on the Lippert SolidStep 4.0 RV Steps item #LC65DX extends 6" past the opening of your RV's doorway. It's only 3/8" tall though. When the steps themselves are folded up and not being used…
Hey Donny! For your Dometic Penguin/Brisk Air 15,000 BTU AC model B59516.711C0-MX, the correct soft start is the #DMC93JF. This is designed for Dometic Brisk II electronic air conditioner units with in-wall thermostats.
Hey Woody, For your 2025 Grand Design Reflection 337RLS, I don't think you'll have any trouble getting either the MORryde RV Cargo Slide Tray - 72" x 39" - 2 Way Slide - 80 Percent Extension - 500 lbs #MR33FR or the MORryde RV Cargo…
Hey Randy! The cost of those replacement parts can definitely get out of hand. The right MORryde StepAbove RV Steps will depend on the measurements on your motorhome. You will need to measure your doorway width (from inside flange to inside flange)…
Hey Nicholas, thanks for the pics and information. To replace your Dometic Brisk II 9105304474 AC, I recommend the Advent Air RV Air Conditioner System item #ADV92SR in white or item #ADV62SR in black. There's no way to just replace your AC unit…
Hey Nick, thanks for reaching out. Yes, the Replacement Fabric for etrailer Powered RV Awnings #e96QV will work with other brands of awning like Solera or Dometic which are what we commonly see on campers like your 2011 Forest River Cherokee 29U. The…
Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hello Theresa, Yes, the TorkLift GlowStep Revolution #TLA8002 will work on your 2022 Forest River Aurora 18BHS based on the measurements you provided. Your 24 inch ground clearance is right within the operating range for the 2-step #TLA8002, and the…
Hey Scott. To add a 7-way and 4-way connector to your 2024 GMC Sierra 3500 that can be used at the same time, I recommend the TowSmart ProClass Trailer Connector item #TS49RR. It's going to replace the factory one and mount in the same position…
Hey John! You weren't finding that SolidStep because Lippert discontinued it in 2024 and that table wasn't updated to reflect this. What I recommend instead is the MORryde StepAbove RV Steps #MR26RR. These are designed to fit 23-3/4" to…
Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…
Hi Frank, The In-command system does limit our options for what air conditioners we have that'll work with that system. You can replace your Coleman AC with the Dometic FreshJet 3 RV Air Condition part #DMC94JF and install the Dometic Climate…
This site is top notch: Great prices, great service. Highly recommended.
Scott
Lafayette, CO
Electric RV Steps with 30 Inch Width
Go for a roomy, sure-footed entry with 30 inch wide steps powered by an electric drive. Measure your entry height and mounting bracket width to confirm a match, and check your door switch type since some systems use a normally open switch. The combination gives you comfortable footing with powered convenience at the door.
Installation can be straightforward when the mounting pattern matches. On older motorhomes the bolt pattern may not fit, but there's often room on the plate to modify. Support the step's weight during fit-up and use proper fasteners. If the process feels over your head, consider experienced help to avoid alignment and wiring issues.
Yes, many have replaced a 2-step with a 3-step and appreciated the extra width and easier first step. Verify your entry height so the 3-step lands comfortably. Check the retracted depth and ground clearance so it won't hit obstacles. Confirm the mounting bracket width and hole spacing before ordering.
Measure your entry height and the mounting bracket width to match an Electric Step. Compare your RV's mounting hole spacing to the specs to ensure the bolt pattern lines up. If the pattern differs, check that there's room on the mounting plate to adjust. Confirm you have space for the step to extend and retract without interference.
Match harness colors first and test the Electric Step; if it works, cap any extra wire like a second red lead. That extra wire may have fed an accessory such as a light. Verify your door switch type—some setups need a normally open switch and may not work with a magnetic style or a normally closed switch. Swap the switch type if needed.
Filters
