This Kwikee 36 Series replacement step extends and retracts smoothly using a 12V motor that ties into the included switch kit. The 30" wide, 10-7/8" deep tread gives a solid feel underfoot, and the 4-5/8" drop/rise makes stepping up or down feel natural. It’s built for a comfortable, steady entry every time.
The step is made from sturdy, powder-coated steel with solid steel drive rods and stainless steel bushings for added strength. It holds up to 300 lbs without flexing, and the air-pressed rivets at pivot points are designed for long-term durability. It’s a dependable, heavy-duty design that stands up to repeated use.
The non-slip tread keeps traction firm even when wet, and the reflective strips along the edge make each step easy to see in the dark. That means safer footing for everyone, whether you’re coming or going at night or in rainy weather.
If the step meets an obstacle while extending, it automatically retracts to prevent damage. The switch kit allows manual control from inside, giving you direct operation when needed. A built-in 4-way plug connects to your existing harness, and a 4-way pigtail is included for hardwiring if needed.
With a 29-7/8" wide x 11-3/8" deep mounting plate and a 31-1/2" overall width, this replacement matches existing Kwikee 36 Series mounting points. It fits into place cleanly using the same bolt pattern—26" wide x 8" deep—for a straightforward replacement that restores the function and feel of the original step.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today you're going to be taking a look at the lifter components quickie 36 series single electric step. Stepping up into your RV can be a bit of a challenge. Especially if the steps aren't working. That's where our replacement steps are going to come into play. With our step installed, when we open the door it's going to automatically come out allowing us to step in easier getting in our RV but at the same time when we close the door, they're going to automatically retract making sure they're not going to catch on anything when we're driving down the road.Now from the top where it's mounted behind this panel, our step is going to drop down a total of five inches. In our application and the step we're using is going to be 24 inches wide by 10 and three quarter inches deep.
There is another step that is available that's going to be 30 inches. To see our website for your specific application and it's going to be made of a nice solid steel construction and have a nice black powdered finish for long lasting durability.The hidden amber light underneath our step is going to make it a lot easier for us to find that step in low light situations and have confidence when we're getting in or out of our RV. The included motor on our step is going to have a solid steel drive rod as well as stainless steel bushes for extended life of the motor. Our steps come with a door switch allowing it to know when to open up and when to close.Now our step is also going to come with a rocker switch in case you choose to manually turn it on and off and not use that door switch. Now that we've seen our steps and gone over some of the features, we do realize that every RV is going to be slightly different but we'll go ahead and give you a brief overview of how to get them in place.To begin our installation, you're going to need to remove your steps and disconnect al the electrical components that are on the steps themselves.
So I got our new step here and we're going to have our pigtail that we're going to wire into our motor home. Then the pigtail is coming off the step as well as the ground wire.So to get our step extended to make it a little easier to work with, I'm going to go ahead and plug in our pigtail and then I have a jump box here which is going to provide my power and grout. So I'm going to take the green wire with the ring terminal on it. I'm going to hook it to ground. I'm going to take my red wire, hook it to power, and then now we're going to take our jump box and turn it on and that should extend the step out.
We've made it a little bit easier to get access to our mounting holes.It's a good idea to have something underneath the step to support it. I'm using a floor jack to help me get the new step in place. It takes a little bit of patience to get everything lined up because it is rather hard to see but once we get the holes lined up, we can put our hardware in hand tight so that step will support itself and we can come back and tighten it all down.Typically you're going to have four bolts, one on each corner holding your step in place. There may be more but you just want to make sure that you replace them all and get them all nice and tight. Now these are the wires that we cut and as you can see they have some inaudible 00:03:15 connectors on them.
That's because it was hardwired into the motor. Now we're going to use the other end of the pigtail and then just connect our wires here so we can have a quick disconnect and if any issues arise we can disconnect it. It would be a little bit easier rather than cutting and splicing every time.So we'll go ahead and cut back these butt connectors and strip the wires and start attaching everything color for color. We're going to take a heat shrink butt connector and now these don't come with our kit but if you need some you can pick some up on our website. Then we can take the other end of our pigtail and we'll find the brown wire. It's already prestrippe.d So we can just put it into the other end of our butt connector and crimp it in place. Now we're going to do that for each one of our wires and we're going to connect them color for color. You should have a white, a yellow, and a red left on the motor home end as well as the pigtail end.We'll be using a heat gun to shrink down the connectors. I just want to mention if you are using an open flame you want to be extra careful not to burn the wires or the connectors themselves. Now this is where our ground from our previous step was installed. I'm going to go ahead and remove that bolt, take our new ground wire, slide the bolt and washer around it, and line up the hole and reinstall that bolt. With the jack out of the way, we can go ahead and shut our door. We can go ahead and go back underneath and start cleaning up all those wires.That'll finish up your look of the lifter components quickie 36 series single electric step.
Ratings & Reviews
Product fitted our needs and was here q uick.
Everything is exactly what it should be thank you for your excellent service I got the package the following day which is even earlier than you originally mentioned great thank you
This step is a big upgrade from the original steps. Much better mechanism and smoother operating than the original.
Box came damaged and opened. The step arm is bent as well on one side. Hole in the bottom of the box where the bent portion was sticking out.
Sad :(
Fast and easy transaction.
As usual etrailer exceeded my expectations. The step arrived much sooner than expected. Very sturdy step and an exact replacement for our damaged one so it should go right in.
Easy to install and has worked great ever since.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.