Hello Bruce, Thanks for writing in! Using butyl tape between the trailer body and the Single Axle Jeep Style Trailer Fender - Diamond Plate Aluminum - 13" to 15" #HP96VR is exactly the route I would go. It stays flexible, creates an…
Hey Bob. There's two possible locations for the brake controller port on your 2026 Ford F-150. The most likely one is on your dash behind the coin holder above the 4WD knob. It'll be connected to the back of the coin tray which is only…
Hey Brian! Yes, the Firestone Ride-Rite Air Helper Springs #F89VV will fit your 2025 Toyota Tundra. That is just the generic picture attached to that page, I can see how it would be confusing. These are designed to mount over the axle, and are…
Hey Jason! For your 2026 Ford F-450 I recommend the Redarc Tow-Pro Liberty Brake Controller #RED67CR. This comes with a custom wiring harness that will plug into the factory brake controller port under the dash. The Liberty is simple, reliable, and…
Hey Kevin, yes we have the SumoSprings kit part #SS46KJ that is a fit for your 2025 Chevrolet Silverado 2500 HD. This is the medium density foam spring provides 2,800-lb support capacity at 50% compression and also requires no drilling for install!…
Hello Paul, There is one thing I like to have when I'm out enjoying the wilderness, and that's a toilet that feels like I'm at home. Well, I found just that for you. Since you're replacing the Dometic 300 in your 2021 Winnebago Minnie…
That is correct Trevor! The Progressive Dynamics 4500 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel item #PD4590K18LS8 would be the correct replacement. This is a 90-amp 2-in-1 AC/DC distribution panel and converter charger that…
Your current microwave has the dimensions of 29-15/16 W x 16-7/16 H x 15-3/8 D which is almost identical to the Furrion part #FMCM15SS which we know works really well and is reliable so it would be a really great and easy solution.
Hey Arlen, welcome back! For a hitch I recommend the Curt Adjustable Width Trailer Hitch #13703. This Class III hitch fits 22" to 72" wide trailer frames and can be bolted or welded on for installation. It has a max tongue weight of 350 lbs…
Hey Robert & Carol, That part number comes back to a custom order piece. Is this the channel on the side of your RV that the fabric from your awning slots into, like part #LC715216? If you'd like to email me some pictures I'd be happy to…
Hey Tim, I checked out your Predator 5000 generator and it does use a quick connect propane connector like what the part #CAM57629 provides so yes this would work. How do you like the Predator generator?
Hey Pam, welcome back! To replace your Pentair Shurflo Revolution 4008 Series By-Pass Pump, I recommend the Seaflo Diaphragm Pump for Boats and RVs item #SE57FR. This is a 12v powered three gallon per minute pump that is rated up to 55 psi. It works…
Dial in the fit on your pop-up camper with RV door parts like latch-and-catch sets and catches made for secure travel. Options include non-locking latches you can leave unlocked or secure with a lock through the loop, zinc-coated pieces to resist rust, and choices with about 1/2" of adjustment and approximately 5-1/4" hole spacing. You'll also find catches around 1-1/4 inch wide by 1 inch high for tighter spots.
Possibly, if the threads match. One hook bolt option is size 12 with 20 threads per inch; confirm your latch uses the same size and thread before swapping only the hook. If it doesn't match, replace the full latch and catch to ensure proper fit and function.
Decide if you want non-locking latches. These are not self locking; you can feed a lock through the loop if you want to lock them. Match your existing hole spacing and adjustment range for a clean swap—one option has about 1/2" adjustment and approximately 5-1/4" from the bottom latch holes to the catch. Verify color and finish to match your camper.
Installation can be straightforward, often reusing existing screw or rivet holes. If included Phillips screws start stripping during install, consider reusing your original hardware. Align the catch so the latch pulls the roof tight; some replacements may be larger than originals but still work fine when positioned correctly.
Yes, zinc-coated latches help resist rust. If the coating gets scratched or wears through, exposed steel can rust, so inspect finish and touch up as needed. Stainless options are not currently offered. In salt air and humidity, a durable coated finish can make a noticeable difference over time.
Catches
Holders
Latches
RV Door Parts Parts or Accessories
Filters
