Customers compare CE27610 to these similar products
Products Featured in this Video
Today we're going to be taking a look at and installing the CE Smith Roller-Style Guide-Ons for Boat Trailers, part number CE27610. Keep your boat centered during the loading process despite wind and waves with these roller-style guide-ons. They help support your boat and keep it centered while loading it onto your trailer. The 13-inch rubberized rollers help protect your boat and gently guide it… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
It sounds like you'll need to do some fab work in order to get the guide-ons to work. I believe your best bet would be to eliminate the u-bolts and have the brackets welded to the top or the underside of the frame member. If the fender step…
view full answer...Yes, the Peterson LED Trailer Tail Lights Driver #PE27RV and Passenger #PE87RV will replace your Shore Land'r 5110570 and 5110569 tail lights. Rather than reusing the push connect wiring from your current tail lights I recommend picking up…
view full answer...Though we do not have an option that would have a perfect 90 degree angle, I may still have something that would work. The CE Smith #CE27610 is a little smaller and typically installed on the outside of a trailer frame, but can be used however…
view full answer...You are correct that the roller style guide-ons #CE27610 are not meant to support weight. But the boat brushing up against them is to be expected and they will work fine for that. A little bit of space like you said will help to make sure the boat…
view full answer...The CE Smith Keel Roller for Boat Trailers - Self Centering #CE29505 is a replacement roller for a keel roller assembly. This self-centering roller fits a 12" wide bracket with a 5/8" shaft. In order to use this on your boat trailer you…
view full answer...I have a few options to help with loading the boat on the trailer but the best would have to be the CE Smith Keel Roller for Boat Trailers part #CE29505. In order to mount them you'd need the Roller Shaft with Pal Nuts part #CE10727A and CE Smith…
view full answer...the CE Smith guide-ons #CE27610 are approximately 15 degrees off 90 degrees. So that would be 75 or 105 degrees depending on which way the guide-on was facing.
view full answer...Based on the information I could find for the DICO 45264 is was popular on ShoreLand'r trailers. This would require the Idler Hub #AKIHUB-545-35-G-EZ-K with the Grease Seal #168255TB used instead of the seal included with the hub. We currently do…
view full answer...To be on the safe size, I recommend going with a 13 inch bracket #CE10002G-4 at the back of the trailer and an 11 inch bracket with #CE10003G at the front. A nice feature on these brackets is that they will each actually have as much as 3-3/4 inches…
view full answer...In terms of capability the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX89FR is a good replacement option. The problem is the design of your old TDE LP7000 which was installed inside the tongue…
view full answer...I'm guessing it is approximately 3-3/8" across if you measured it. Unfortunately there are no options that will slide in because it won't line up correctly, and everything is designed to fit a 3" tongue so it is too wide to mount an…
view full answer...You can convert surge brakes to an electric over hydraulic braking system. To do this, you will need an electric over hydraulic actuator and a brake controller. For an electric over hydraulic actuator, I recommend looking at the Carlisle HydraStar…
view full answer...