Boat Trailer Parts - Spool Roller

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

Hey Tim, most likely the trailer hub part #AKIHUB-545-35-EZ-K is correct for your trailer as it most likely has a 3,500 lb capacity hub with a 5 on 4-1/2 inch bolt pattern but I would need for you to verify your axle capacity for me as the fits are…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

Hey Mike! Sounds like you're needing the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-EZ-2K. If you're wanting something with a better protective coating the Galvanized Hub #AKIHUB-545-2-G-EZ-2K will do the trick, but…

Hey Fred! If you have an even number of bolt holes you can measure center to center between opposite holes to find the bolt pattern. If you have an odd number of holes you measure from center to the farthest edge. See the attached photo. For example,…

Hello Todd, We definitely have something for you, but we do not a radial tire and wheel combo, as we only have that tire and wheel combo in a bias. It depends on your bolt pattern, and the weight of your boat to decide what the best option for you.…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat…

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

Hey Jacob, the pigtail harness part #100575-12-MBS that you referenced would work great for each of your propane tanks to attach to the JR Products Auto Changeover Regulator #37207-31525.

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

Hey Tim, most likely the trailer hub part #AKIHUB-545-35-EZ-K is correct for your trailer as it most likely has a 3,500 lb capacity hub with a 5 on 4-1/2 inch bolt pattern but I would need for you to verify your axle capacity for me as the fits are…

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

Hey Mike! Sounds like you're needing the Easy Grease Trailer Idler Hub Assembly for 2K Axles #AKIHUB-545-2-EZ-2K. If you're wanting something with a better protective coating the Galvanized Hub #AKIHUB-545-2-G-EZ-2K will do the trick, but…

Hey Fred! If you have an even number of bolt holes you can measure center to center between opposite holes to find the bolt pattern. If you have an odd number of holes you measure from center to the farthest edge. See the attached photo. For example,…

Hello Todd, We definitely have something for you, but we do not a radial tire and wheel combo, as we only have that tire and wheel combo in a bias. It depends on your bolt pattern, and the weight of your boat to decide what the best option for you.…

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

The size winch that you will need depends on a couple of different factors. I have included part of our hand winch FAQ below regarding boat winches and have linked the FAQ article for you to view. Finding the Right Capacity Winch for your Boat…

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

Hey Jacob, the pigtail harness part #100575-12-MBS that you referenced would work great for each of your propane tanks to attach to the JR Products Auto Changeover Regulator #37207-31525.

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…