2018 Jayco Redhawk Motorhome Brake Controller

Features:

The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The unit plugs into your 7-way for a one-step installation with no wiring.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The unit plugs into your 7-way for a one-step installation with no wiring.

Installation Notes:

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The unit plugs into your 7-way for a one-step installation with no wiring.

Installation Notes:

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The unit plugs into your 7-way for a one-step installation with no wiring.

Installation Notes:

You need item ETBC7L ($94.89) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. It's so easy to adjust your settings or activate manual override.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. It's so easy to adjust your settings or activate manual override.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This proportional brake controller keeps it simple with intuitive controls that are easy to use. Includes a large, digital LED display, 3 boost levels, battery protection, and continuous diagnostics.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.

Installation Notes:

You need item ETBC7L ($94.89) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

Features:

Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.

Installation Notes:

Features:

Wireless brake controller mounts on your trailer to keep your cab clutter-free. Keep towing simple and convenient with a handheld, Bluetooth remote control. Nothing installs in your vehicle, so you can tow with any truck that has a 7-way.

Installation Notes:

Features:

This unique brake controller mounts on your trailer instead of in the cab so you can tow your trailer using any truck. You'll control your settings from the handy key fob remote.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

Features:

This unique brake controller mounts on your trailer instead of in the cab so you can tow your trailer using any truck. You'll control your settings from the handy key fob remote.

Installation Notes:

Features:

This unique brake controller mounts on your trailer instead of in the cab so you can tow your trailer using any truck. You'll control your settings from the handy key fob remote.

Installation Notes:

Features:

This unique brake controller mounts on your trailer instead of in the cab so you can tow your trailer using any truck. You'll control your settings from the handy key fob remote.

Installation Notes:

You need item ETBC7L ($94.89) to install your controller.

Features:

This proportional brake controller automatically syncs to your vehicle's computer network for smooth, precise braking. Low-speed brake adjustment gives you 2 settings for different speeds. Plug-and-play controller mounts in any direction.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

This proportional brake controller automatically syncs to your vehicle's computer network for smooth, precise braking. Low-speed brake adjustment gives you 2 settings for different speeds. Plug-and-play controller mounts in any direction.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

The Tekonsha P3 is a brake controller beloved for its reliability and useability. You're able to save your settings and multiple profiles. It's easy to install, and with the custom harness, it's plug-and-play.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

The Tekonsha P3 is a brake controller beloved for its reliability and useability. You're able to save your settings and multiple profiles. It's easy to install, and with the custom harness, it's plug-and-play.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

The large, digital, LED display and clearly labelled buttons on this proportional controller make it easy to use. Includes 3 levels of boost, a slide-bar manual override, built-in short circuit protection, and automatic leveling.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

The large, digital, LED display and clearly labelled buttons on this proportional controller make it easy to use. Includes 3 levels of boost, a slide-bar manual override, built-in short circuit protection, and automatic leveling.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The plug-and-play unit mounts under your dashboard, out of sight and out of your way.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The plug-and-play unit mounts under your dashboard, out of sight and out of your way.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

The Tekonsha P2 is a classic brake controller you know you can rely on. It's easy to install, and with the custom harness, it's plug-and-play.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

The Tekonsha P2 is a classic brake controller you know you can rely on. It's easy to install, and with the custom harness, it's plug-and-play.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This compact brake controller fits nicely in your cab. It's designed to mount flush to the dash and is only 1" thick. The controls are simple, the LED display is large and bright, and the manual override is easy to reach in a pinch.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

This compact brake controller fits nicely in your cab. It's designed to mount flush to the dash and is only 1" thick. The controls are simple, the LED display is large and bright, and the manual override is easy to reach in a pinch.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. It's so easy to adjust your settings or activate manual override.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. It's so easy to adjust your settings or activate manual override.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

The large, digital, LED display and clearly labelled buttons on this proportional controller make it easy to use. Includes 3 levels of boost, a slide-bar manual override, built-in short circuit protection, and automatic leveling.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

The large, digital, LED display and clearly labelled buttons on this proportional controller make it easy to use. Includes 3 levels of boost, a slide-bar manual override, built-in short circuit protection, and automatic leveling.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

You can stick the control knob to the dashboard, plug in the module, and your brake controller installation is done with no drilling and no hardwiring. The knob is large and easy to use, while the main unit is out of sight behind the dash.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This compact brake controller fits nicely in your cab. You can mount it anywhere you like and it's only 1" thick. The LED display keeps it simple with bar indicators, while the large manual override is easy to reach in a pinch.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This compact brake controller fits nicely in your cab. You can mount it anywhere you like and it's only 1" thick. The LED display keeps it simple with bar indicators, while the large manual override is easy to reach in a pinch.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. Its unique off-roading mode helps you handle rough conditions, so get out there and get towing.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This is one of our favorite brake controllers, with flawless braking and a tiny dash knob that looks like it came straight from the factory. Its unique off-roading mode helps you handle rough conditions, so get out there and get towing.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Mount the control knob of this proportional brake controller on your dash for a from-the-factory look, and install the main unit out of sight behind the dash in any position or angle. Adhesive backing gives you the option of a drill-free install.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Mount the control knob of this proportional brake controller on your dash for a from-the-factory look, and install the main unit out of sight behind the dash in any position or angle. Adhesive backing gives you the option of a drill-free install.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This time-delayed brake controller is designed to mount at any angle, even upside down. The controls are all up front for easy access, including a slide-bar manual override and a thumbwheel for braking output. LED indicator shows your braking status.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. Plus, it's plug-and-play, so no splicing and no permanent alteration to your vehicle.

Installation Notes:

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. Plus, it's plug-and-play, so no splicing and no permanent alteration to your vehicle.

Installation Notes:

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. Plus, it's plug-and-play, so no splicing and no permanent alteration to your vehicle.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

Features:

Simple and rugged, this time-delay brake controller is able to install in any direction, even upside down. Includes a large digital display with a dark smoke lens that can be read even in direct sunlight. Activates brakes with a preset intensity.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Simple and rugged, this time-delay brake controller is able to install in any direction, even upside down. Includes a large digital display with a dark smoke lens that can be read even in direct sunlight. Activates brakes with a preset intensity.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The plug-and-play unit mounts under your dashboard, out of sight and out of your way.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Towing? There's an app for that. This brake controller connects to your phone with Bluetooth so all your settings are right in your hand. The plug-and-play unit mounts under your dashboard, out of sight and out of your way.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Simple and rugged, this time-delay brake controller is able to install in any direction, even upside down. Includes a large digital display with a dark smoke lens that can be read even in direct sunlight. Activates brakes with a preset intensity.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Simple and rugged, this time-delay brake controller is able to install in any direction, even upside down. Includes a large digital display with a dark smoke lens that can be read even in direct sunlight. Activates brakes with a preset intensity.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Get a brake controller in your truck that looks like it's supposed to be there. This sleek knob blends right into your dash and makes your settings simple and convenient to adjust.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This brake controller likes to keep things simple, with a thumbwheel on the front to adjust the output settings and a lever on the side for the sensitivity. The digital display is large and simple so you can read it with just a glance.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

This brake controller likes to keep things simple, with a thumbwheel on the front to adjust the output settings and a lever on the side for the sensitivity. The digital display is large and simple so you can read it with just a glance.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

This compact brake controller fits nicely in your cab. You can mount it anywhere you like and it's only 1" thick. The LED display is large and bright so it's easy to see, while the large manual override is easy to reach in a pinch.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

This compact brake controller fits nicely in your cab. You can mount it anywhere you like and it's only 1" thick. The LED display is large and bright so it's easy to see, while the large manual override is easy to reach in a pinch.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.

Features:

Adjust power output and braking aggressiveness with easily accessible, up-front buttons on this time-delayed brake controller. Digital display and rotary-style manual override included. Activates brakes with a preset intensity.

Installation Notes:

Vehicles with the 7-Way tow package have the blue output brake wire already ran from the back to the front. It is located under the dash near the emergency brake pedal.

If your vehicle has a round plug with a cap inside the driver's side frame rail instead of a bundle of wires in the jack storage compartment, use part # 30955.

Some models will require a wiring kit to run wire to the battery. This may require drilling a hole in the firewall to run the wire. You may use kit 5506 which includes 20, 30, and 40 amp breakers.

Tech Tip:

Some models will have the connection wiring taped and tucked under the driver side floor mat up towards the firewall.

Features:

Adjust power output and braking aggressiveness with easily accessible, up-front buttons on this time-delayed brake controller. Digital display and rotary-style manual override included. Activates brakes with a preset intensity.

Installation Notes:

You need item ETBC7 ($124.38) to install your controller.

You may also need a 4-Flat connector to complete your wiring.

Features:

Adjust power output and braking aggressiveness with easily accessible, up-front buttons on this time-delayed brake controller. Digital display and rotary-style manual override included. Activates brakes with a preset intensity.

Installation Notes:

The brake controller can easily be installed with the included vehicle specific wiring adapter; no other parts are necessary.

Features:

Adjust power output and braking aggressiveness with easily accessible, up-front buttons on this time-delayed brake controller. Digital display and rotary-style manual override included. Activates brakes with a preset intensity.

Installation Notes:

You will also need item 37185 ($57.57) to complete your wiring.

The brake (blue) wire will need to be run from the brake controller back to the plug in the rear. The brake controller power and brake pedal wires are already run. A 12 volt hot lead from the battery may also need to be installed.