See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring

• How Much Ground Clearance Will Curt Hitch Have for a 2009 Kia Optima
  Hey Veronica, thanks for reaching out! When we installed the Curt Trailer Hitch Receiver # C11351 on a 2009 Kia Optima we found that from the ground to the top inside of the hitch receiver was 9-1/4" so from the ground to the bottom of the receiver is going to be about 7-3/4" so you'll want to test this out to see if you'll have adequate clearance or not. You'll also need to install the T-One Vehicle Wiring Harness # 118433 and pick up a ball mount. I'm attaching a helpful article that...
  view full answer...
• Will Draw-Tite # 24795 Fit my 2010 Hyundai Elantra with a Recovery Tow Loop
  The Draw-Tite hitch #24795 will fit your 2010 Hyundai Elantra as long as it is the Sedan model. We have test fitted the product on a Hyundai Elantra with a tow loop and I attached photos of the hitch on the vehicle. The hitch sits right in front of the tow loop and it does not interfere with the use or installation of the hitch. If your Elantra is a Touring Hatchback, this hitch will not fit and you will need Draw-Tite Hitch Receiver #24844. This hitch has a powder coat finish to ensure...
  view full answer...
  
• Hidden Hitch # 60872 vs. Draw-Tite # 24795 for a 2010 Hyundai Elantra
  The main difference between the Hidden Hitch Trailer Hitch Receiver, part # 60872, and the Draw-Tite Trailer Hitch, part # 24795, is that the # 60872 (no longer available) has a drawbar, pin and clip included with it, whereas the # 24795 does not include those things. Aside from that, they are so similar in design that they even share the same installation instructions. I attached the instructions and a video of this product being installed onto a similar car as yours below for you to...
  view full answer...
• Will Tow Loop on 2010 Hyundai Elantra Interfere w/ Trailer Hitch Installation
  The hitch will fit perfectly, no worries. When we installed the Draw-Tite Class I hitch, # 24795 on a 2010 Hyundai Elantra, we found that the receiver tube will sit just aft of the tow loop you mentioned, as you can see in the photo I've provided. If you plan on using the hitch for light duty towing, you'll need a few other items to complete your towing system: Trailer wiring harness, part # 118433 Ball mount, part # 3594 1-7/8 inch trailer ball, part # 19256 or 2 inch ball # 19258 Pin...
  view full answer...
  
• What Do I Need to Tow a Motorcycle Trailer with a 2007 Hyundai Sonata
  The components needed to tow a trailer include a trailer hitch receiver, ball mount, pin and clip, trailer hitch ball, and a wiring harness. I have included an article which covers this. To get your 2007 Hyundai Sonata ready for towing, I recommend the following: Trailer Hitch - Draw-Tite Class I Trailer Hitch Receiver, # 24757. This is a custom fit hitch offering a 2,000 lb towing capacity and bolt-on installation. No drilling or welding is required. Ball Mount - Sportframe Drawbar,...
  view full answer...
• Trailer Hitch Receiver Availability For a 2008 Hyundai Sonata Towing a U-Haul Trailer
  Currently the only receivers available for your 2008 Hyundai Sonata are class I like the Curt Trailer Hitch Receiver # C11325. This is mostly due to your Sonata having a maximum towing capability of 200lbs tongue weight and 2,000lbs or total trailer weight. Be sure to check your owners manual for your maximum towing capacity. Curt recommends using the Ball Mount # C45521 in the rise position. You will be able to use either a 1-7/8" Ball # C40001 or 2" Ball # C40018 with the U-Haul trailer....
  view full answer...
• Trailer Hitch Recommendation for a 2011 Hyundai Sonata Hybrid
  The Draw-Tite Class I 1-1/4 Inch Hitch, part # 24965, will fit your 2011 Hyundai Sonata Hybrid. This hitch does not include the ball mount. To install on your vehicle you will need to lower the exhaust and the heat shield will need to be trimmed. I am including a link to the installation instructions on the Draw-Tite. The instructions will show in detail where the heat shield needs to be trimmed. If you will be towing with this hitch you will also need the following items. Tow Ready 2...
  view full answer...
• Hitch Recommendation for a 2007 Hyundai Elantra Sedan
  I have a hitch that is confirmed to fit your 2007 Hyundai Elantra sedan, but the part # C11493 that you referenced will not fit. Instead, you would want the Draw-Tite part # 24795 as it has been confirmed to fit your vehicle. I attached an install video for this hitch for you to check out as well. This hitch does not come with a ball mount but does have a pin and clip. To complete your towing setup you may also want the part # 118433 for wiring, # 19256 for a 1-7/8 inch hitch ball, and...
  view full answer...
• Trailer Hitch and Vehicle Wiring Recommendation for a Single Exhaust 4-cylinder 2006 Hyundai Sonata
  Yes, the Draw-Tite Class I trailer hitch will fit all models of the 2006 Hyundai Sonata, including your 4-cylinder with single exhaust. Our tech tips note that vehicles with single exhaust, the appearance panel which covers driver's side frame rail must be removed. This is a Class I rated hitch that is rated for towing up to 2,000 pounds gross towing weight and 200 tongue weight, and is compatible with Class I 1-1/4 accessories only. Since it is Class I hitch, the manufacturers recommended...
  view full answer...
• Recommended Trailer Hitch for a 2011 Hyundai Accent
  We actually have a ton of feedback on the Draw Tite Hitch part # 24795 being installed and used on a 2011 Hyundai Accent. This hitch has nearly a perfect rating from our customers who have it. If you go to the product page for the hitch and then click the reviews tab that is right above the product description you will see all of the feedback we have for this hitch. You may also be interested in purchasing the following products: Hitch Ball with 1-7/8 inch Diameter and Short Shank, part...
  view full answer...
• Which is the Correct T-One Wiring Harness for 2006-2009 Hyundai Sonatas
  I just looked up the 2006-2009 Hyundai Sonatas, and the T-One Wiring Harness, part # 118433, is in fact the correct wiring harness for those vehicles. I want to reassure that you did, in fact, order and receive the correct part for your vehicle. Sometimes the packaging on the parts can be misleading, as the parts may be compatible with several different makes, models and years.
  view full answer...
• Will Draw-Tite Trailer hitch # 24844 Fit the 4 Door Sedan Model of a 2009 Hyundai Elantra
  We have several hitches that are specifically designed to fit the 2009 Hyundai Elantra sedan. The trailer hitch that you have referenced, # 24844, is designed to fit the 2009 - 2011 Hyundai Elantra Touring Hatchback, so it will not fit the sedan. The difference is that # 24844 has a longer receiver tube so it is not too far under the vehicle. The Sedan rear end has a different shape so the receiver tube is shorter. The comparable trailer hitch for a sedan model is # 24795. I have included...
  view full answer...
• Does the Exhaust have to be lowered to Install a Trailer Hitch on a 2009 Hyundai Sonata
  Installation on a 2009 Hyundai Sonata with single exhaust is going to be nearly identical as in the video showing installation of Draw-Tite Trailer Hitch, # 24757, on a 2010 model. The two different years are part of the same generation and the hitch attaches the same way in both models. This is quite possibly the easiest installation I have seen for a hitch. Even the instructions, which I have linked for you, have just 2 steps. Neither our installers nor the hitch manufacturer mention...
  view full answer...
• Can Wiring Harness # 118433 from 2010 Hyundai Sonata Fit 2014 Sonata Non-Hybrid Model
  Thank you for your 2011 purchase of a wiring harness. That actual part you ordered is Tow Ready harness # 118433 which is intended for 2006 through 2009 model years of the Sonata. It is not a confirmed fit for the 2010 Sonata, please note. The recommended harness for your 2014 Hyundai Sonata non-hybrid is Curt # C56049 which is shown in the linked video. This harness installs without any cutting or splicing of wires thanks to its custom-fit connectors. There is no resetting function for...
  view full answer...
• 2 inch Hitch Ball, Ball Mount and Wiring Recommendation for a 2008 Hyundai Sonata
  Anytime you use a hitch adapter you end up cutting the capacity of the hitch by 50 percent. Because of that I tend to avoid recommending them as an ideal solution. Since your trailer has 2 inch hitch ball coupler you would want the # 3592 for a ball mount and then for a 2 inch ball # 19258. For trailer wiring you would then want the part # 118433 which I attached an install video for as well.
  view full answer...
• Will the Draw-Tite Hitch # 24757 Fit on a 2010 Hyundai Sonata SE, with Dual Exhaust.
  Yes, the Draw-Tite Sportframe Class I Trailer Hitch, item # 24757, will fit on your 2010 Hyundai Sonata SE, with dual exhaust. The under body appearance panel noted in the instructions, is only present on single exhaust models and needs to be removed for hitch installation, dual exhaust models do not have this panel and the hitch installs without removal of any parts. To complete your Class I Towing setup you may also want to consider the following items. Custom Fit Vehicle Wiring # 118433 Ball...
  view full answer...
• Does the Bumper Have to be Removed or Replaced to Install a Trailer Hitch on a 2010 Hyundai Elantra
  To install the Draw-Tite Trailer Hitch, # 24795, on your 2010 Hyundai Elantra, you will not have to remove or replace the bumper. There is some minor fascia trimming required. A tab on the bottom center of the fascia will need to be trimmed in order for the hitch to fit properly. I have included a link to the installation instructions that include an illustration of where this trimming will occur. I have also included an installation video on a similar vehicle. If you plan on towing with...
  view full answer...
• Availability of a 2 Inch Trailer Hitch Receiver for a 2011 Hyundai Sonata Limited
  Draw-Tite trailer hitch # 24965 is a fit for your 2011 Hyundai Sonata Limited, but it does have a 1-1/4 inch hitch opening. I am sorry, but we do not have 2 inch hitches available for your vehicle. To wire your vehicle for towing, you would use custom-fit T-One vehicle wiring harness # 118433. Hitch # 24965 does not include a ball mount. You would also need a hitch ball if you plan on towing a trailer. You would most likely use a hitch ball with a 1-7/8 inch diameter, like part #...
  view full answer...
• Trailer Wiring Recommendation for a 2010 Kia Optima
  Yes, I checked with Tow Ready and the Wiring Harness part # 118433 that you referenced has been confirmed to fit your 2010 Kia Optima so I would recommend it for you. I attached an install video that shows it being installed on a 2009, but the process will be the same for you.
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?