Will Optronics Trailer Connector w/ Coiled Cord 7-Way Round to 5-Pin Delphi Replace Malibu 6832001.1

Question

Question:

Optronics Trailer Connector w/ Coiled Cord - 7-Way Round to 5-Pin Delphi - 12V Optronics Custom Fit ? I was wondering if this would fit a 2022 Malibu boat trailer. 7 to 5 Way Trailer Coil Wiring Harness - Malibu Trailer 6832001.1

asked by: jeff k

0

Expert Reply:

Hey Jeff, I did some checking and the Malibu part number 6832001.1 is exact same as the Optronics Trailer Connector w/ Coiled Cord # OPT48NB that you referenced so this would be the correct replacement. Did you lose your current 7-way or did it get damaged?

expert reply by: Jameson C

0

Jeff K.

7/14/2026

Damaged. Dry rot seems to be a pretty common issue with the Malibu plugs. Hopefully this will last longer than those.

Jameson C.

7/14/2026

@JeffK understandable! How long did the Malibu one last and was it exposed to saltwater?

Jeff

7/14/2026

@JamesonC 3 years, no salt water but it’s stored outside all summer

Jameson C.

7/14/2026

@Jeff yeah outside can be rough but three years does seem too short of a time.

Answer 1

It is hard to say exactly how much of the black wire insulation was cut off of the 7-Way Round RV Style Trailer Connector #A7WCB, but after watching the video and having done this myself before, it looks like Rick cut off about 2 inches of the black…

view full answer...

Answer 2

Hello Mike, Your old brake actuator only had one wire because it grounded through the trailer frame, which was pretty common back in the day. Your new Dexter DX7.5L actuator #DX89FR has two wires coming off the electric lockout solenoid no worries,…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Will Optronics Trailer Connector w/ Coiled Cord 7-Way Round to 5-Pin Delphi Replace Malibu 6832001.1

Product Page this Question was Asked From

Continue Researching