Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Drop leg adds 8" of additional lift for your etrailer or Ram A-frame jack with a 2" diameter inner tube. Extension can be adjusted in 2" increments. Corrosion-resistant, zinc-plated finish. Pin and clip included.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 2: Today we're going to be taking a look at the drop leg for the etrailer and ram jacks. This measures 13 1/4 inches tall and has a five diameter foot plate with a zinc finish. The part number is JF-1005H-Z. Now here's what our drop leg looks like installed. This gives us a total of eight additional inches that we can add to the end of our inter-tube of the jack here, just so we don't have crank so long to get the jack fully extended. This is going to give us five locations to choose from for a total of eight inches of adjustment here.
The biggest benefit you're going to see about a drop leg like this is one, the time savings, but also we don't have to worry about the narrow lift of our jack digging down into the mud or the sand or the gravel, whatever it might be. This gives us a full five inch circle that's going to come down and make contact with that material. Again, dirt, sand, gravel and it spreads that energy out over a greater area so we don't have to worry about our jack being sunk down in or actually dropping down below our ball mount when it sits there for an extended period of time. We will just use a jack stand to simulate attaching our trailer to our vehicle. This is where the big benefits are coming in. Rather than us having to fully retract our jack the whole way up, we can stop at that point once we have the weight off the plate.
We'll just pull our pin out and then lift our drop leg up into position. Once we have it lined up with that highest setting, you'll see that it's going to be nice and high. It doesn't add that much to the end of the jack leg there, so we won't have to wor4ry about hitting it or bumping it or anything like that. Next time we're ready to unhook our trailer, simply pull our pin, extend that back down, we've got a lot less work ahead of us to get that coupler off of our ball. We've also got a couple of small holes here so if any mud we're to happen to get up on the foot plate, sand, or water, it can just run out of those so it won't build up there causing corrosion down the road. To install our foot plate, we basically just need to line up the groove that is in the back side of it here with that same groove that's on the inner tube of our jack and then we'll align one of the holes here. Now these holes are on two inch centers and you'll just take the provided pin and clip, it's going to slide through our hole and we'll secure it there on the other side.
Then it's just a matter of operating our jack. That's going to complete our look at the Drop Leg for the etrailer and ram jacks, part number is JF-1005H-Z.
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
Ratings & Reviews
Leslie
12/12/2024
Works great, easy to use and no heavy blocks to carry. Faster setup.
Russ M.
1/2/2022
Product is still working great with no problems. Perfect solution for a low-riding trailer hitch where the foot can scrape.
Danny
10/14/2023
The down leg has been one of my better investments. I will buy one for my next trailer jack.
Mike L.
11/5/2023
Do you have a question about this Accessories and Part?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Kate F.
5/14/2026
Thanks for the review Brian! I'm glad the install was quick and easy and that the jack fit perfectly, even on a different brand setup. It’s always nice when a simple upgrade works exactly the way it should. Thanks for sharing the picture too. The setup looks great! What kind of trailer are you using this on?