Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
If you’ve been running older incandescent lights, this UltraThin ID Light Bar is a big upgrade. It uses three red LEDs that are brighter and more efficient while drawing only 0.038 amps at 12.8V. The light bar is 15" long x 1-3/8" tall x 5/8" deep, giving plenty of coverage across the rear. It’s P2 rated for strong, forward visibility that keeps your trailer visible to others in dark or low-light conditions.
When space is limited, the ultrathin design makes installation simple. At just 5/8" deep, it fits neatly without sticking out or catching on anything. The mounting holes are spaced 14-1/8" center to center for a clean fit on most setups. It surface mounts directly to the trailer and uses a straightforward 2-wire design—one power lead and one ground—so wiring is quick and tidy.
Moisture and road spray are no problem for this light bar. The red polycarbonate lens and housing are sonically sealed into one waterproof unit that’s completely submersible. It keeps water away from the diodes and circuit board, making it a dependable choice for trailers that see wet roads or full submersion during use.
This light bar eliminates the hassle of replacing fragile bulbs or dealing with corroded sockets. The solid-state LEDs last up to 50 times longer than incandescent lights and don’t rely on filaments that can break from vibration or impact. You get a reliable light that stays bright for years with practically no maintenance needed.
For trailers wider than 80", this identification light bar meets DOT requirements for rear clearance lighting. The three-diode setup creates a clear, even red signal so your trailer stays compliant and visible wherever you haul.
Customer Satisfaction Score:
100% were satisfied with this product
0% of customers were not satisfied
Ratings & Reviews
Cheapest LED light out there. Great quality and even better service!
Great quality product for extra visibility on my enclosed trailer
Fast shipping works great
very nice looking / its nicer than the one that cam with the trailer that I broke.
Easy to install, quite bright. Was the best solution for my tilt bed trailer.
Great product quality.....Right on time. This is my second order from Etrailer.com> They will be getting my business in the future.
Great people to deal with and quick shi pping.
Product was described as is. Knew what I was getting. Fast service getting to me in Alaska and didn't charge an arm and a leg for shipping!
I used this on the rear of my car trailer. Worked great and brighter than the stock ones. However, I smashed it backing into a tree. This one worked so well I’ll probably just buy it again.
Arrived on time well packaged with no damage and was what was advertized. Mounted easily on my trailer, the LED's are brighter than the 3 marker lamps it replaced. A Good product at a reasonable price.
Your suspension parts and the wiring components exceeded my expectations. Just as pictured and very good quality. I'll be back again and again You're easy to do business with and the shipping is very prompt. Good job, folks!
like the slim design. Seems like the marker lights on flatbed trailer are always getting broken and the slimmer design helps protect them some.
Needed this for a flatbed trailer I bought that needed to be brought up to standards for it's size. Bought many things from etrailer.com. Good prices, good quality, good information.
I was disappointed that I didn't catch that despite being 14 inches long, it only has 3 working LEDs.
The help and service provided by this company was stellar. They helped me get exactly the same size light as came out of the motorhome in only a few minutes.
Use them!
excellant online shopping , shipping was fast
Awesome looking light. These units are slightly shorter than the stop/turn/tail with reflector. It would be nice if they matched or if there was shorter stop/turn/tail with reflector to match it, but only 1/4 inch difference not too bad. Also, the LED circuit board is open on the back side of the light. I will be filling it with silicone or dielectric grease before mounting and then caulking around the mount to make it water tight.
Happy with purchase. Appropriately bright. I ran the white wire inside the trailer chassis and grounded it; I could have just as easily run it to one of the self-drilling light bar mounting screws. Like another reviewer, I flexible-caulked around the light bar.
Great product, fast service.
I have bought several items over the past few years from etrailer and get great customer service and good products always. The prices are good and the time it takes to get the product is pretty fast.
Pat M.
10/27/2017
the products that i purchased work just as i expected them to and your company is great to work with
Quick delivery
The right part was shipped
This is why I return to etrailer
Thank you.
I use these as step lights on my 5th wheel RV. They are exposed to the elements and mounted behind the tires and have never failed.
Gary
12/13/2024
Still working as advertised.
Great service, great fit and works as described. Videos and staff are very helpful.
Appears to be an exact duplicate of the OEM light on my 2017 Ranger Trail trailer. Aligned perfectly. (Check your mounting hole measurement b4 ordering). Time will tell as to it's waterproofing, but for the cost... if I get 37 months out of it, it will have outlasted Ranger's OEM light that cost $xx+ to replace
Michael M.
5/12/2023
After 12 months, I havent had any issues and it is working as expected.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
David
3/22/2016
tks , it works great