Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
When you want strong, efficient light without the fuss of frequent bulb changes, this small oval LED delivers. The Dragon’s Eye design uses 2 amber LEDs that shine bright while drawing less power than old incandescent setups. At 2-5/8" long and 1-1/4" tall, it puts out a clean amber glow that improves visibility day or night. With no filaments to break, these LEDs last up to 50 times longer, so you spend more time towing and less time replacing bulbs.
Good lighting isn’t just about output—it’s about how well you’re seen. The Dragon’s Eye lens projects light not only outward but also back onto the mounting surface, creating a glow that goes beyond a 180-degree view. That broad coverage helps others spot your trailer from more angles, adding another layer of safety when driving or parking in low light.
Water damage can ruin ordinary lights, but this one is built to handle the elements. The clear polycarbonate lens and housing are sealed for weatherproof protection, keeping moisture out even during wet conditions or heavy road spray. Whether it’s a weekend trip or tough daily use, this light stays sealed and dependable.
Getting it mounted is straightforward. It installs on the surface using standard hardware (not included), with mounting holes spaced 1-15/16" center-to-center. The single wire design grounds through the mounting hardware, cutting down on extra wiring steps. Compact at only 3/4" deep, it fits neatly against the surface for a clean look that stays out of the way.
You don’t have to wonder if it meets the right standards—this light is both SAE and DOT compliant. That means it’s approved for road use and ready for duty as either a clearance or side marker light when properly mounted. Backed by a 1-year warranty, it’s a tough little light that’s made to last.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're gonna be taking a look at and showing you how to install the Dragon's Eye LED Clearance or Side Marker Light.Now this is what the light's going to look like when it's turned on. As you can see, the two diodes put off more than enough light. I really like it because it's LED, which means you're not gonna have to worry about any brittle filaments breaking like your traditional style incandescent lights, and it's gonna use less power to put off a brighter light.Another reason I like this light is because how compact it is. It's going to measure only 2-5/8" long, 1-1/4" tall. From bolt hole to bolt hole, it's going to measure 1-15/16" and it's going to be 3/4" deep.The light is DOT compliant. It is a great upgrade from an incandescent light, because the LEDs last a lot longer.
It also has a weather proof housing to help resist any water damage.And this is what the back of the light looks like. As you can see, we have one wire coming out, this'll be our power wire. And we have a built in ground strap that will get grounded from our mounting hardware. Now this is a really neat feature, because it eliminates the need for another wire coming out of the back of the light.And I'll show you how easy it is to install this light. Now depending on your application, you may have to drill a few holes for your hardware, and one for your wire to pass through.
And it's a good idea to drill the center hole a little bit bigger, that way your wire doesn't get hung up on it. Now it'll do that because this center portion here is the same height as the outside part of the light, and if your hole happens to be small and off-center, when you run your wire through, it could pinch your wire like that. So we're gonna avoid that.Once you have that done, feed it through, and push your light flat up against your trailer's frame. Alright, now we're gonna secure the light using some Number 8 Self-Tapping Tek Screws. Let's get both of 'em started, and use our wrench to tighten 'em down.
And you wanna be careful not to over tighten these, 'cause you don't wanna crack the lens. So just run 'em down until they stop, and they're nice and snug.Alright now all we have to do is connect our trailer's power wire to the light's power wire. We're gonna do that using a Heat Shrink Butt Connector, which you can find on etrailer.com. We'll place it over the light power wire, crimp it down. And do the same thing to the trailer's power wire, and you can use a heat source to shrink our heat shrink.Now with everything connected, go ahead and test it to make sure everything works.
Once we do that, we can use some zip ties and secure our wiring up out of the way to help keep it protected. If you have more than one light, just go ahead and repeat that same process to get the rest of 'em installed.And that'll do it for our look at, and installation of the Dragon's Eye LED Clearance or Side Marker Light.
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews
Easy to install and has been working gr eat!
A perfect fit for my trailer
Easy to order and arrived quickly.
Very valued supplier with quality parts and excellent customer service!
Excellent service, shipping and product s!
Perfect match to the ones on our trailer, thanks
Great service! They stand by there word which is rare these days !
Perfect replacement!
Quick shipping, good products
Everything worked great would buy again. Thank you
My purchase was easy to match my existing light, ordering was simple, and received it quickly. Great price too!
Exact replacement for my toy hauler. Will buy more.
Just got, works just as good as the other one I installed.
exact match needed
Victoria H.
3/8/2025
That's perfect Roy!
Great customer service arrived ahead of schedule. Finally a company with Good customer service. You've got My Business. However I'd like a catlog Thank You.
Harold
2/19/2024
Well Its just fine but I never did get a response to or receive a catalog
Are good replacement parts
Incredible light with 2 diodes. Used stainless phillips self-tapping #8 screws to mount the light. The negative terminal is hard contact to a side terminal. 6" positive 18 gauge lead cable. Order the snap on plastic chrome cover to finish the look.
I have an Anvil enclosed trailer and these lights are the stock style markers the trailer came with. They were simple to install, worked as expected (nice and bright) and fairly priced. They have been on the trailer for 9 months and show no sign of product failure.
Website is easy to navigate with clear descriptions and pictures making it easy to find what you are looking. Prices are good and each time I ordered I received the product in just a few days. Highly recommend.
The nicest marker lights I've seen! Discrete and yet bright at the same time!
Love the look. Finicky to keep working with the one wire version.
Excellent customer support, very friendly and knowledgeable. I would highly recommend this company
The customer service at etrailer is above and beyond any other company! Issues are always addressed and resolved. I will always do business with them since they help with ordering if needed and are there should you need post sale assistance.
Great LED marker lights.
This was our first time ordering from etrailer. Seamless transaction, great communication, parts arrived earlier than expected, and staff followed up to make sure we were happy. Great resource to keep our race rigs ready to go!
Mike L.
12/3/2025
Awww, thanks Dave! I'm glad we could help!
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Steven B.
11/1/2023
Lights still look and work like new.