Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This Optronics mini light uses two red LEDs that shine bright while drawing just 0.06 amps at 12V. The LEDs last up to 50 times longer than incandescent bulbs, so you won’t be swapping burnt-out filaments or dealing with dim lights again. It’s efficient, clear, and reliable every time you hook up.
If your trailer sees rain or road spray, this light is up for it. The housing and clear lens are sonically sealed into one waterproof piece that’s completely submersible. Moisture and corrosion stay out, keeping the electronics protected so your light keeps working after countless launches or storms.
The body and lens are made from impact-resistant polycarbonate that can handle hits from gravel or gear without cracking. It’s a tough little housing built to stand up to rough roads and daily use, giving you a dependable light that won’t quit when things get bumpy.
At just 2-1/2" long by 1-1/8" tall and only 5/8" thick, this oblong light mounts flat against the surface with two #10 screws (hardware not included). The single-wire design grounds through the mounting hardware, so hookup is quick and clean—no extra grounding wires to fuss with.
This P2-rated marker or clearance light sends a focused 45-degree beam to each side of center for a total of 90 degrees of coverage. It produces a bright red output through its clear lens, helping other drivers see your trailer’s edges clearly at night or in low-light conditions.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everybody. Andy here with etrailer.com. And today, we're gonna take a look at this Optronics submersible, mini red LED clearance or side marker light. With this little oblong waterproof LED trailer light, you are gonna be able to haul safer by alerting other drivers of your trailer's position and direction of travel. As you can see, I already have this connected to 12 volt power. And this light functions as both a clearance and side marker light when properly mounted.
This is how bright it is with my studio lights on. Let me go ahead and turn my lights off to give you a better idea what this is gonna look like, especially at night. Now, these two red LEDs can last 50 times longer than incandescent lights. They're more efficient. They provide brighter light with less power output.
There's no bulbs replace or no brittle filaments. This is a P2 rated light, meaning that it produces a 45 degree angle of light to either side of its center line for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side, so this type of light can be used as either a side marker light or a clearance light, but it cannot be used as both. So, if you need both a functions, then you must install two separate lights on your trailer. One as a front or rear clearance light, and one as a side marker light.
This light features a sonically sealed, waterproof housing and a lens unit that is submersible. And it has an impact resistant, polycarbonate housing and lens. And the transparent lens help produces a clear, colored light. This is a surface mounted light and surface mounts to your trailer with two number 10 screws. Those screw are not included, so you would have to get that either locally or a separate purchase.
And this is a single wire design that grounds through the mounting hardware. Now, this is compatible with 12 volt DC systems and the power draw at 12 volts is 0.06 amps. Just give you an idea of the size of this light. Looking at the overall length of this light from end to end, we are sitting right at 2 1/2 inches long. And looking at the width, we're sitting right at about an inch and an eighth wide. Line that up here a little bit better for you. And then the thickness, we're sitting right at about five eights of an inch thick. And then the distance between those mounting holes, center to center, line that up here for you, we are sitting right at 1 7/8 inches. Now, there is a lifetime warranty on the two LEDs. And that is going to conclude our look today. I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me..
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Brooke M.
2/25/2025
Thanks for the photo as well as all the tips about install. Its nice knowing what other peoples first hand experience was. Thanks!