2-1/2" x 1-1/8" Oblong. Waterproof LED trailer light serves as a clearance or side marker light when properly mounted. Durable polycarbonate housing and lens. Surface mount - hardware not included. 1-Wire design. P2 rated.
Features:
Specs:
Surface-mount trailer lights install using a flange or bracket with mounting holes. These lights lay flat against the trailer surface and only require a small, often pre-existing hole, for wiring. Mounting hardware is used to secure the light to the trailer.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Ellen: Hey, everyone. I'm Ellen here at etrailer.com and today we're going to be taking a look at the Optronics Mini Amber LED Clearance or Side Marker Light.Now, this is going to be a great upgrade from the old incandescent bulbs that you've probably had on your trailer. These are going to last a lot longer because light is also submersible. It's sonically sealed, so it's going to make it all waterproof. You can take this out on your marine trailer, boat trailer, or anything like that and you don't afford about any water getting in there and causing any issues. Also, a nice thing about our LEDs is that they're going to be brighter, more efficient, but also there's no bulbs to replace with this so there's no maintenance required.
It's going to last for a long time. Pretty much should be able to install it and then forget about it for many years. Unless it breaks, something hits it, pretty much going to be good for a long time.It does have a clear lens over amber LEDs. We'll have two diodes there. This is P2 rated and basically that just means that you can only see it from a limited range so it can't operate as a side marker and a clearance light.
It operates as one or the other, kind of depending on where it's placed on your trailer. We have more information about that at etrailer.com. If you look at the product page for this, it'll give you a better illustration of exactly what I mean there, but basically it just needs to be one or the other. It can't be both your clearance and your side marker light.I'm just going to connect this up to power and ground. You'll notice that it has one wire.
That's going to be for power. The ground connection is made whenever you put your hardware through there, and then that metal connects with the ground wire going into our light. You'll want to install this on a good piece of sturdy metal on your trailer to make that ground connection. Flip my power source on here. We can see how bright this light is.
Ta-da, it's on.Has a power draw at 12 volts of 0.046 amps, so a very low power draw. This really isn't going to tax your system much at all, so you can have a whole bunch of these if you so desired. I'm going to turn out the lights in the studio just so you can get a better idea of how bright that light is for using it at night. Not blinding but enough to function as intended.There is a lifetime warranty on those LEDs. So again, you really shouldn't have any worries with this burning out anytime soon. Going to unplug everything and then we'll go over some measurements. Turn that off, disconnect my wires.As far as the length, from the outside edge of the housing it's about 2-1/2" long. The distance between those mounting holes center to center is right at about 2". The width is just a hair over 1", about 1-1/16". Then the height or depth, however you want to look at it there, is just under 7/8", so it's about . Or, excuse me, yeah, 7/8" at its tallest point there. There's a little notch on either side so you can put that power wire down through and you don't have to worry about smashing it and causing any issues to tear through that wire, so keep it safe there going in either direction. The length of the wire coming off of it, it's about 6-1/2". Stick it to my ruler there.All in all, it should be a great addition to any trailer. Now, this does not include any mounting hardware, so you will have to pick up some screws. Two #10 screws should work out just fine. Compatible with 12 volt DC systems. And that housing is made of a durable polycarbonate.And that's going to do it for our look at the Optronics Mini Amber LED Clearance or Side Marker Light.
Average Customer Rating: 4.8 out of 5 stars (34 Customer Reviews)
2-1/2" x 1-1/8" Oblong. Waterproof LED trailer light serves as a clearance or side marker light when properly mounted. Durable polycarbonate housing and lens. Surface mount - hardware not included. 1-Wire design. P2 rated.Exactly as described. High quality LED. Lights
It was delivered on time and works great I tell everyone to use e trAiler
Perfect replacement for my old lights. Same size and shape.
They were a perfect match to the existing lights on my trailer and simple to install. I have had no issues since installing them. Thanks for the follow up!
Love my clearance lights and they match the ones on the trailer. Very bright and easy to hook up. If I need more etrailer is the place that I will shop. I'm very happy with all of their products so far.
Good quality is better than the one I'm replacing. The lead wire could have been a little longer which would have made it a little quicker and easier to install.
Wanted toads more to our trailer and they are awesome. Love etrailer products.
Ended up needing the two wire marker lights rather than the one wire.
The one wire light appeared to be ok just not for me.
These work great! Save time soldering, cut-strip-heat!!!
They are still working and look good
Great product, great service...just what I wanted.
Exact replacement part. Perfect fit.
It's a good product very happy with it thank you
Nice lights at an affordable price. Delivery was quick as well.
Just we needed
Fast service and very fair price
Product was as advertised, quick shipping and good price.
Thank you!
Fast shipping great communication!!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.