Kit includes everything you need to switch your trailer over to disc brakes for improved performance and greater stopping power. Actuator has an electric lockout that activates automatically to keep brakes from actuating when in reverse.
Features:
Specs:
Bearing, Race and Seal Information
Complete kit includes:
Disc Brakes
An increasing number of trailer owners are switching over to disc brakes, and with good reason. Disc brake calipers have only one moving part, as opposed to the many moving parts you find with drum brakes. This means that with disc brakes there are fewer parts to maintain, fewer parts to get damaged and fewer parts to repair or replace, thus reducing the cost of maintenance.
Performance increases as well. Disc brakes deliver consistent braking even at highway speeds, unlike drum brakes, which often show a substantial drop in braking torque at higher speeds. In addition, disc brakes offer a much shorter stopping distance than drum brakes.
This complete disc brake kit makes the conversion easy. Designed for single-axle trailers, this kit includes not only the disc brake assemblies themselves - along with all the necessary lines, fittings and mounting hardware - it also contains an actuator. This hydraulic brake actuator has a higher psi rating for disc brake applications and includes an electric reverse lockout so that you can back up without activating your trailer's brakes.
The electric lockout is automatically activated when you shift your tow vehicle into reverse. The included solenoid wires into your trailer connector - which connects to your tow vehicle - so that it can detect when you are in reverse. When your vehicle is in reverse, the solenoid ensures that the hydraulic actuator does not activate your trailer's brakes, thus allowing you to back up your rig. To use the lockout feature, you must have a 5-pole flat, 6-way round, or 7-pole trailer connector.
Hydraulic Line Kit
Note: If you intend to run brake lines along the axle of your trailer to install disc brakes - as is often done for boat trailers - you will need 1 additional hose (T4890700 - sold separately) and 1 extra hose clip (T0776400 - sold separately) with bracket (T0776300 - sold separately) to complete the installation.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to review part number T4843500. This is the Titan Disc Brake Kit and the Aero 7500 Actuator. This is for a single 3,500-pound axle. This all-inclusive kit has everything you need to switch your trailer over to disc brakes, comes with two disc brake kits, the hub and rotor assemblies, the grease seals, the bearing protectors, races -- the racers are actually pre-installed in the hub and rotors-- and all the bearings, inner and outer bearings. Comes with the calipers with the mounting brackets right here. These brackets are designed to attach to the four-bolt brake flange, so you do need to have the four-bolt brake flange on your axle.
If you don't, we also sell the weld-on brake flanges separately on our website. The hub and rotors and the calipers are all silver cadmium-plated. The Aero 7500 brake actuator, this comes also, this is the hydraulic actuator which will synchronize your trailer brakes with your tow vehicle brakes. Right here at the front, you can see this lock-out. This is actually a manual reverse lock-out. This will let you reverse without actuating your trailer brakes.
That's a pretty easy-to-use lever that will activate the lock-out. You just click in it to activate it, release it to deactivate it. This actuator has zinc plating, which is corrosion-resistant. If you'll notice the wire wrapped around here, this is the break-away kit, which is also included. It is a simple bolt-on installation. Also included is this bag, which is a hydraulic line kit, has the brake lines and fittings for a single axle. Your disc brakes will deliver better performance compared to your drum brakes, gives you more consistent stopping at highway speeds and even shorter stopping distances than most drum brakes.
Again, on this kit, the application is for a single-axle trailer with a 3,500-pound axle. It does use a wheel size of 14 inches to 15 inches. On the hub and rotor itself, does have a diameter of 9 3/4 inches, has a bolt pattern of five on 4 1/2 inches and it is designed to use half-inch lug nuts. On the caliper mounting brackets, they do use the four-bolt brake flange configuration, as I mentioned earlier. You can see that there. On the actuator, it is designed to fit on a two-inch diameter ball size.
It does mount on a three-inch-wide channel tongue trailer. The capacity on this actuator is 7,500 pounds. The maximum tongue weight capacity on the actuator is 750 pounds. Basically, this part number includes everything show here, the actuator, hub and rotors, calipers, brackets, all the bearing seals, bearing protectors and the hydraulic line kit. That should do it for the review on part number T4843500, The Titan Disc Brake Kit with the Aero 7500 Actuator for a single 3,500-pound axle. .
Ratings & Reviews
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
















Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.