See what our Experts say about this Deka Wiring

• Recommended Trailer Wiring Harness For A 2025 Hyundai Tucson SEL
  Hey Tim, The ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT is compatible with LED lights and has been used as a go to for years for people who have LED trailer lights. The light function is supposed send a tiny bit of voltage from the vehicle tail lights to the converter box so it knows what signal to send out the 4-pole connector to the trailer. If your tail lights are staying on like that question you saw then the shop either spliced the wrong wires together or the converter...
  view full answer...
• Recommended Battery Monitoring System For RV Batteries To Help Prevent Overcharging
  The fact that your converter overcharged your batteries leads me to believe it's replacement time for your converter since it isn't properly functioning. That being said we do offer monitoring systems like the Go Power RV Battery Monitor Kit with 25' Cable # GP44FR. This monitoring system will allow you to easily see the charge rate and consumption of your batteries and can also let you set shutdown alerts when the voltage is too low or high. If you want to replace your WF-8735P then...
  view full answer...
• How to Install an Amber Turn and Parking Light on a Trailer with Combined Brake and Turn Signals
  Many people inquire about wiring a trailer in the way you describe, and it is possible, but you will need to use a vehicle to vehicle taillight converter, part # 118158, to accomplish this. The converter will be wired inline on the trailer wiring and will break out the turn and brake circuits. I attached a drawing that shows how I would go about wiring this converter on a simple 4 wire trailer. You would just need to cap off the red wire on the output side of the converter and tie that...
  view full answer...
  
• Replacement 5th Wheel LED Tail Light for a Round Red Light
  Thank you so much for your photos. We don't have an exact replacement light for you, but we have something very close. It's the Optronics LED Trailer Tail Light, part # STL13RFHXB. This LED light measures 5-5/8" in diameter (almost exactly what your current one measures) and has the three mounting holes. It features the 7 diodes that your current one seems to have and the same three functions. Most importantly, it's round and fully red. This is a flush-mount design, so there is a difference...
  view full answer...
  
• Can I Use Existing Switch on Ford F-250 to Install Power On/Off of Custom 3rd Brake Light Camera
  Yes. There is no reason that you can't just use the upfitter switch in your Ford F-250 to connect the power of the Custom 3rd Brake Light Camera # 3460006 instead of installing a new switch. I've linked an installation video we did that you can use as a reference, as well.
  view full answer...
• Adding A Brake Controller To A 2024 Tesla Model Y
  Hey Anthony, It looks like there's a proprietary pigtail wire harness (p1072586) to connect to the factory plug behind the trim on the driver's side and the brake controller's wire harness. From what I can find some people say that it's included and should be found in the glove box and others state that Tesla's completely against giving them out to Model Y owners. I would check to see if you have it and if not reach out to Tesla. There's a couple of videos out there where people have...
  view full answer...
• Installing Brake Controller in 2009 Chevrolet Silverado
  The Draw-Tite Activator IV # 5504 will work with a wiring harness adapter like part # 20127, for your 2009 Chevrolet Silverado. This means you will need to splice into the brake controller wiring under the driver's side dash in order to install the brake controller. There will be a bundle of wires tied together with white tape. These are the wires you will to connect your adapter to. You will want to connect the black brake controller adapter wire to the red factory brake controller wire,...
  view full answer...
  
• Brake Controller Recommendation for 2021 Jeep Grand Cherokee
  I see that you'd looked at both the Redac # RED24FR Tow-Pro Liberty as well as the Tekonsha # TK90160 Primus. Either controller would work well, to answer the question of which would be the best controller for you will depend on how familiar you are with brake controllers, your budget and whether you'd be satisfied with a traditionally mounted brake controller that would bolt to the underside of the dash like the Primus or whether you'd prefer a remotely mounted controller like the Tow-Pro...
  view full answer...
• Which Wiring Harness Will Be Needed to Install the Optronics GloLight LED Trailer Light STL178RFPB
  The proper hardwire wiring harness for the # STL178RFPB GloLight LED trailer tail light is the # A47PB. A great and similar style side marker/clearance and turn light is the # STL78AB, this will already have the proper wires to install on your trailer. If you prefer it to be a GloLight like your tail lights we do have one from Optronics # STL111AB. The wiring harness you will need to install the GloLight # STL111AB to your trailer is part number # A47PB. Since the GloLight LED doesn't...
  view full answer...
  
• Replacing Trailer 5-Way That Has Each Circuit Split Into Two Wires
  That specific version of 5-way is not available at this time but the # A25W5B is the closest solution we have to this. It has the brown wire "wishboned" or split for either side of the trailer but the rest of the wires are a single wire per circuit. So what you'd need to do is run both of the wires you have on your trailer to the single wire on the 5-way and you'd be set. For butt connectors we have the part # DW05714.
  view full answer...
  
• How To Switch from Jenson RV Stereo JRV212T to Jensen RV Stereo JWM60A
  There is no adapter harness to convert the wiring from the Jenson JRV212T to the Jensen RV Stereo part # JWM60A. That said, this is actually pretty simple using the attached diagram. All you'll need is some wire crimpers/strippers like part # PT43ZR and butt connectors like part # DW05714. Just match wires from the old unit to the new unit by function and you're good to go.
  view full answer...
  
• How To Wire In The MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan
  The two MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan # MA00-03851 you bought will have black and white wires hidden above the fan that you'll connect to the 12v wiring of the trailer. The black wire is your power and the white wire is your ground/neutral. To connect it to the trailer's wiring you'll need to use some butt connectors # DW05714 or wire nuts to splice the wiring together. If there isn't 12v wiring in the locations near the vents then you'll need to run some 14 gauge wire...
  view full answer...
• Installation of Midship Marker and Turn Signal Light on 1996 Holiday Rambler Endeavor
  Good news! I can help you wire up a mid-ship turn signal your 96 Holiday Rambler Endeavor, but the Optronics light # MCL32AB you asked about will not blink while you have the running lights on. What you will need is the Amber LED Mid-Ship light with flange # STL75AMFB. I recommend using butt connectors # DW05714 and 16 gauge wire # 16-1-1 to make the connection to the diode from the original circuits. I have linked all the above mentioned products to this page for your purchasing convenience.
  view full answer...
• Recommended Replacement LED Puck Lights For A 2018 Tiffin Allegro Motorhome
  Based on the pictures you provided it looks like you have a 4-1/4" surface mounted puck light. We don't have replacement PCB LED boards I do still have two replacement options for you: Option 1: Glantastic 12V RV LED Puck Light # 328-K-58L34P9. This light has is 4-1/4" in diameter but requires a cutout hole approximately 3-1/4" in diameter. You could trim the current hole a bit more to make this fit. Option 2: Gustafson 12V RV LED Puck Light # 277-000341. This light is 5" in diameter...
  view full answer...
  
• Recommended 2-Inch Trailer Hitch for Use on 2016 Keystone Hideout Trailer
  We have both bolt-on and weld-on 2-inch frame-mount hitches available for your Keystone Hideout trailer that can be seen by clicking on the included link. All of these have a square cross tube, 2-inch receiver opening and are rated for either 3500-lbs or 5000-lbs gross trailer weight. In your application I recommend one of the higher-capacity hitches. You'll want to check your trailer's frame width for a proper fit. Hitch # UF35-946403 from Ultra-Fab is a bolt-on type that fits frame...
  view full answer...
• Is there a Backup-Alert Reverse Light for Bulb Type 921 for the 2013 Chevrolet Equinox
  Your 2013 Chevrolet Equinox uses a type 921 backup light bulb. The Hopkins product you reviewed, part # HM20101VA, is a replacement for the type 3156 bulb. My contact at Hopkins advises that they do not offer an audible alarm replacement bulb for the 921 type. I also checked with two other suppliers of aftermarket lighting products, Putco and Optronics, and neither of these suppliers offers a 921 replacement bulb with alarm. However, we do offer the Custer Surface Mount Back-up Alarm,...
  view full answer...
• How to Wire Tekonsha Sentinel Brake Controller in 2007 Chevy Suburban
  Your 2007 Chevy Suburban will have tow package wiring under the dash and typically these wires will be red, dark blue, light blue (or orange) and white. These tow package wires should be below the steering column to the left of the brake pedal and tied together with white tape. It sounds like you have found the correct wires although the colors may have faded slightly from age. The RED wire from the Suburban connects to the BLACK wire on the controller; the DARK BLUE wire connects to...
  view full answer...
• Options for Different Connector Styles for Solera RV Awning Motor
  We have replacement motors for Solera/Lippert awnings that have a two pin connector like the part # LC373566. This is for awnings that were made after 2015. For awnings made before 2015 we have the part # LC266149. This uses two wires with spade connectors instead. We don't offer any adapter harnesses but if you have something different you could pretty simply just use butt connectors to make the connection like the # DW05714.
  view full answer...
• Wiring Location to Connect a Brake Controller to a 2017 GMC Acadia
  The stop light switch wiring is located behind your brake pedal on your 2017 GMC Acadia. See the picture for a visual. If you are having trouble locating the wire you can use a Circuit Tester # PTW2993 to find out which wire sends a signal when the brake is depressed. You can use a Quick Splice Wire Connector # SWC501746-1 or a Butt Connector # DW05714 to connect the red wire from your brake controller to the stop light switch wire on your Acadia.
  view full answer...
  
• Wire Gauge of USB Power Outlet for RVs - 2 USB Ports 37215115
  14 gauge wire is used with the USB Power Outlet for RVs - 2 USB Ports # 37215115. So you can connect the wires with two of the Butt Connector - PVC - for 16-14g Wire # DW05714. Then to mount it in the correct plate is the Mounting Plate for 12V Socket or USB Outlet # 37215155. I have added some links below to video reviews for you to check out as well.
  view full answer...
• Recommended Wire Gauge Needed to Extend Vent Fan Power Wire to Charge Controller
  To wire up your Ventline vent # VP-543SP the correct gauge wire needed is a 16 gauge like # DW02359-1. You will also want to use the 16 gauge buttconnectors like # DW05714 to connect the two wires. You definitely want this to be connected to a fused power source so if your charge controller isn't fused then on the 16 gauge wire you would want to wire in a 5amp fuse to protect the unit.
  view full answer...
• When is it Recommended To Use Dielectric Grease When Wiring
  We want to thank you for your recent purchase! You wouldn't need to use dielectric grease with a butt connector such as part # DW05714 (view video at the 1:16 mark) as electrical tape will work great. Heat shrinkable tubing such as part # DW05451 will help protect against the elements. It works with 14-18 gauge wire. Most trailer light wiring is 16-gauge. Once you have your wire inside the tubing you can use a heat gun, blow dryer and/or lighter utilize the heat shrinkable tubing. We...
  view full answer...
  
• How To Install the Optronics Thinline LED Trailer Fender Light
  The Optronics Thinline LED Trailer Fender Light part # MCL67ARB comes with a mounting bracket so as long as the surface you will be installing it on is metal then yes, it will work for you. All you would need to do to install the light is use two self tapping screws like part # 1131832 to mount the base and then once this is done you can attach the light to the base. To complete the process you will then need to attach the black wire to the running light circuit on your trailer which is...
  view full answer...
• How To Fix ABS Error On 2016 Toyota 4Runner with Tekonsha Trailer Brake Controller
  The solution to fixing the ABS Error on a 2016 Toyota 4Runner with trailer brake controller like the Tekonsha Primus IQ Trailer Brake Controller part # TK90160 is to combine the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers part # 3041-P and Pigtail Wiring Harness with Diode part # 7865. Just cut the brake controller end off the first harness and splice on the one from the second. You need a diode on the red wire to stop back feeding which is what is causing the error message...
  view full answer...

Do you have a question about this Wiring?