Can I Use Existing Switch on Ford F-250 to Install Power On/Off of Custom 3rd Brake Light Camera

Question

Question:

The video mentions small parts that might be needed as well, do you have a list of those part numbers?

asked by: Tara B

0

Expert Reply:

Yes. There is no reason that you can't just use the upfitter switch in your Ford F-250 to connect the power of the Custom 3rd Brake Light Camera # 3460006 instead of installing a new switch. I've linked an installation video we did that you can use as a reference, as well.

expert reply by: Erik B

0

Tara

7/28/2020

The video mentions small parts that might be needed as well, do you have a list of those part numbers?

Erik B.

7/28/2020

Yes! The additional installation parts mentioned in the installation video are as follows: 16 gauge wire # 16-1-1 Butt connectors # DW05714 Ring Terminal Butt Connector # DW05702-1 Self Tapping Screws # FA1131822 Fuse Tap # F2526 The mini fuses mentioned would need to be sourced locally from an auto parts store, but everything else is listed above!

Scott R.

11/5/2021

I have a 2011 F450 Lariat, I have replaced the oem tailgate with an RV Custom Flow tailgate so I no longer have need for the original tailgate camera in the handle, can this camera system be attached to the original wiring harness so it comes on when truck is placed in reverse? I need the camera to show the fifth wheel hitch when connecting/disconnecting from a trailer. The original tailgate camera harness only had three wires attached.

Les D.

11/9/2021

We do not have schematics to know if such a project is possible. The camera mentioned in the article seems like the best solution since you don't need your rear view mirror when hitched anyway.

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Hello Matt, I was seeing some mixed information on this as well, so I reached out directly to my contact at Firestone to confirm. The Firestone Ride-Rite Air Bags w/ Easy Mount Compressor - Wireless Control - Single Path - 5,000 lbs #F44XV will fit…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can I Use Existing Switch on Ford F-250 to Install Power On/Off of Custom 3rd Brake Light Camera

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching