To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
The Adarac Pro Series Custom Truck Bed Ladder Rack handles up to 500 lbs, or 250 lbs per bar, so it’s ready for both job materials and outdoor adventures. You can load ladders, lumber, and pipes during the week, then haul kayaks, surfboards, or skis on the weekend. The crossbars measure 66" long x 1-1/2" wide, giving plenty of space to spread out gear while keeping the truck bed open for other cargo.
This rack mounts securely into the stake pockets, leaving the inside bed rails clear, so it works with most inside-the-rail tonneau covers including hard tri-folds and roll-ups. The vertical uprights don’t angle inward, which means folding or rolling the cover stays easy and unobstructed. You get full use of your cover’s panels and weather seal without removing the rack.
No drilling is needed for installation. Foam-padded utility rails sit on top of the bed rails and use aluminum stake pocket inserts for a solid mount that won’t scratch your truck. The uprights can be repositioned along or removed from the utility rails whenever you need more space for tall or bulky items.
Each square crossbar has mounting channels along the top and bottom, and the utility rails include channels too. That lets you add tie-downs, load stops, or other accessories exactly where you need them. The removable rubber strip on top of the crossbars keeps loads from slipping and can be taken out to access the channels when mounting gear.
The lightweight aluminum construction is rustproof, so it won’t corrode in wet or salty conditions. An extruded anodized aluminum finish adds extra protection and keeps the silver rack looking sharp over time. It’s a setup made for years of hauling, whether you’re on the job or heading out to the water.
Ratings & Reviews
Box came open at one end and slightly open at the other. I was nervous thinking that the hardware bag and two additional accessories that I ordered might be missing. Upon opening the box everything was there and well packaged. The only issue I had was one of the vertical supports that has two laser cut holes didn't have one of the holes completely cut. 3/4 of the cut was made. I punched a starter hole in the center and drilled it out and finished the install. Overall great rack for carting around the canoe or lumber longer than the pickup bed. One other thing. They need to debur the edges of the aluminum pieces otherwise they are very sharp.
Love this ladder rack...it works great with my tauneau cover, Iuse it to transport our Kayaks when we go camping and it is great to still be able to use my bed with the tauneau cover on to protect our gear in inclimate weather. I would absolutely buy it again. Thanks.
This rack is very solid and travels well.
I have had no problems but I should say I have used it lightly.
Super easy to install and looks great. Can't wait to get my boards up there!
Works great with the backflip hard cover.
Should have some predrilled hole to attach tie down straps.
I really like the aesthetics of the ladder rack and functionality. Its sturdy, durable and looks slick !
Package arrived on time I have been out of town for a few weeks so just put it together today
It fit perfectly I think it looks good will mount kayaks on it and see if it works
I am well pleased so far
The ladder rack is great. Fits over my tonneau cover. And carries everything I put up there.
I have had this rack for one year. So far, so good. It looks great, way better than other models I see around. Do not rust; sturdy enough. Works well with trunk cover. Installation is a bit tricky, but any handyman can do it alone in a couple of hours. Good purchase overall
Clean, sleek look. Easy to install!
Took a couple of hours to install. One on the few you can use with hard tri-fold bed cover. Going to add side bars for off-road tools.
After 90 minute install, it feels sturdy and looks great. Ford ranger 2025, no cutting or drilling required. I like the fact that it has some rubber strips on top, should work well for carrying a kayak. Will need to unscrew antenna if carrying something in middle over roof.
I love my Adarac Pro Series Custom Truck Bed Ladder Rack - Aluminum - Matte Black - 500 lbs. I found it easy to install by myself—including cutting the deck plastic trim to expose my stake covers. Its black finish complements my truck. Best of all, it enables my BAK Industries tonneau cover, Revolver X2, to maintain is full functionality. My only recommendation would be to include more foam strips. They are intended to fill the gaps between the end of the grooves on the plastic trim to the end of the rail. There was enough for one strip of foam on each end rather than two (one on each side of the rail) on each end of the rails.
Packaged delivered in good shape. The rack was very well made. It was easy to install. Very sturdy and should hold up well. The Pro model worked with my Bak-flip Tonneau Cover. I would highly recommend this product. I have used etrailer for years and they always come thru.
I had delayed trying to get ladder racks because I wasn't sure whether it would work with my bed cover. I was able to locate the correct model online and verify my findings and order on the phone Rodney was helpful and friendly.
I have had the rack installed for about six weeks. After a few trips on everything from highways to gravel and dirt roads it has been very solid. We have a fly fishing rod case mounted on it and it's solid. I think there is a little wind noise but not much. Easy to install, lots of good paper instructions as well as videos on line. Next trip will have our canoe mounted on top.
I bought this rack believing installation did not require drilling. That may be true for installation on many vehicles, but does require drilling to install on a Jeep Gladiator. Special instructions that come with the rack are quite clear on this for both a Jeep Gladiator and a Toyota Tacoma up to 2023.
A 2nd issue came up while following the instructions. They call for torquing the self threading bold to 85 in/lbs. When I hit 60 in/lbs, the self threading bolts started stripping out the holes. I fixed this using 6 nuts to hold the self threading bolts from underneath. Tight clearances made this a tougher job than it should have been.
To anticipate questions, yes I was using a torque wrench calibrated in inch pounds and not foot pounds. Yes I used the proper drill size and did not wobble the holes larger. I believe that at least for Jeep Gladiator, the kit should include nuts for the hold down bolts. Can't comment on the Toyota Tacoma - but be prepared.
I will say that once installed, the rack looks to be a quality item and I am otherwise satisfied with it. If not for the unexpected installation hassles, I would rate the rack as 5 stars.
Overall good product, works with my trifold tonneau cover, I do wish it had some sort of cover for the stake pocket where the upright bolts in. I wish I came with additional channel nuts as well for bolting onto the crossbars
Easy to install and remove. User friendly and adjustable.
I'm very happy with it.
I bought this ladder rack because I needed something that would attach to the stake pockets of my f-150 because I have a bed cover. Everything else I found had to hook around the side of the truck bed. Installation was easy. The only issue I had was the forward stake holes didn't have a removable cover. I had to cut a hole in each side.I use them to carry my kayaks when I go camping. They work great for that and carrying anything that won't fit in the bed.
Condition: Missing Parts
Notes: surface scratches and missing hardware
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.