See what our Experts say about this CURT Custom Fit Vehicle Wiring

• Installing Curt Trailer Wiring Harness 55260 on a 1995 Jeep Grand Cherokee
  When installing Curt trailer wiring harness # C55260 on a 1995 Jeep Grand Cherokee, both connectors will install on the passenger side of the vehicle behind the tail light and interior trim panels. Look for the matching connectors that look like the gray and black connectors on the harness. This harness is designed to fit on vehicles that have the factory tow package. If yours does not have the factory tow package the wiring may not be present or active for this wiring harness. If that...
  view full answer...
• Which Trailer Wiring Harness Will Fit a 1995 Jeep Grand Cherokee With 5.2L Engine
  The correct harness for your 1995 Jeep Grand Cherokee will depend on if you have the factory tow package or not. This can be verified by contacting a Jeep dealer and having them run your VIN. What they say will determine which is correct. If you end up having the tow package, I suggest going with the Curt # C55260. This is a plug and play option and will take very little time to get installed and using. If you do not end up having the factory tow package, I suggest going with the Tekonsha...
  view full answer...
• Trailer Wiring Recommendation for a 1996 Jeep Grand Cherokee Limited
  Your 1996 Jeep Grand Cherokee Limited most likely came with either no trailer connection at all or a 7-way round trailer connector. If you have a round connector at the rear of your vehicle near the hitch that looks like the part # 20135 then you have a 7-way. To see if you have the connection point to install the wiring harness designed for factory wired vehicles (part # C55260) you will need to look on the driver's side behind the spare. You will see an access panel there. Open it...
  view full answer...
• Installation Instructions for Curt # C55260 Trailer Wiring Harness on 1996 Jeep Grand Cherokee
  If you click the provided link, you can see the installation instructions for the Curt # C55260 trailer connector. Curt does a nice job of providing detailed color photos, which helps make the installation easier.
  view full answer...
• Factory Connector Location to Install Trailer Wiring on 1997 Jeep Grand Cherokee w/Tow Package
  It is possible that the connectors for wiring harness # C55260 will be in a different location on your 1997 Jeep Grand Cherokee than what is stated in the instructions. You may have to pull additional panels out of the way or check the opposite side of the vehicle. Other customers have made similar comments in the review section of this product. One customer said "the included instructions from the manufacture are wrong. for my 1996 Jeep Grand Cherokee the proper vehicle harnesses are...
  view full answer...
• Cant Find All of the Connection to Install Curt Trailer Wiring Harness on 1996 Jeep Grand Cherokee
  The Curt trailer wiring harness # C55260 is designed for models of the 1996 Jeep Grand Cherokee that came with the factory tow package. It is possible that yours does not have the factory tow package so not all of the wiring is present. If you have searched and cannot find that connector anywhere then that is likely what is going on. So instead of harness # C55260 you would need a different harness, # 118349. I have included a link to a video review of this harness for you.
  view full answer...
• Parts to Add 7-Way Wiring to 1998 Jeep Grand Cherokee with Factory Trailer Hitch
  I definitely have some wiring parts so you can add a 4-Way/7-Way connector to your 1998 Jeep Grand Cherokee. There aren't any with that direct plug though so we'll have to piece together a few things to get to that point. To add a 4-Way to your vehicle you need the Curt T-Connector # C55260 which plugs into the factory tow package wiring. If you don't have the factory tow package you'll use the Tekonsha T-One # 118349 instead. Now that we have the 4-Way you can use the Hopkins # 37185...
  view full answer...
• Where Does a Trailer Wiring Harness Plug In on a 1997 Jeep Grand Cherokee
  Curt trailer wiring harness # C55260 is designed for models of the 1997 Jeep Grand Cherokee that came with a factory tow package. If that connector is no where to be found then that likely indicates that the vehicle does not have the factory tow package and you will need a different wiring harness, # 118349, which plugs in line with the vehicle tail light wiring.
  view full answer...
• Curt Trailer Wiring Harness Installation on a 1997 Jeep Grand Cherokee with Factory Tow Package
  On the product page for Curt trailer wiring harness # C55260 there is a section below Features called Installation that reads "This custom-fit T-connector plugs into your Jeep Grand Cherokee's factory tow package wiring harness, which is located behind the passenger's-side interior trim panel in your rear cargo area." So based on this and the instructions you should be looking on the passenger's side. But sometimes the connectors you need to plug into are hidden. You may need to look forward,...
  view full answer...
• Correct 4-Way Wiring Harness for 1997 Jeep Grand Cherokee
  The reason the # 118354 did not fit is because it is designed for the 1997-2001 Jeep Cherokee. The correct wiring harness for your 1997 Jeep Grand Cherokee will depend on whether or not you have the factory tow package. If you have the factory tow package, I recommend the Curt # C55260. If you do not have the factory tow package, then you want the # 118349 instead. These are the most reliable options for your Grand Cherokee with/without the tow package. I have attached some review videos...
  view full answer...
• What Is the Max Towing Capacity Of a 1998 Jeep Grand Cherokee
  According to my research, the most well equipped 1998 Jeep Grand Cherokee has a maximum towing capacity of 5,000 lbs. Unfortunately, we cannot recommend you tow more than this but since you are very close to the maximum towing capacity you would most likely be fine by just going over a few hundred pounds or so. That said, I cannot recommend this so you will just need to use your best discretion on what you think is right for your vehicle. For a trailer hitch, I recommend using the Draw-Tite...
  view full answer...
• Where Does the Black Connector On the Curt Vehicle Wiring Harness for a 1996 Jeep Grand Cherokee Go
  In regards to the Curt T-Connector Vehicle Wiring Harness part # C55260 which is a fit for a 1996 Jeep Grand Cherokee, the black connector will be hooked-up to the right hand taillight and the gray connector will be hooked-up to the left hand taillight.
  view full answer...
• Trailer Turn Signals and Brake Lights do not Work on a 1998 Jeep Grand Cherokee Laredo Limited 5.9
  Since your 1998 Jeep Grand Cherokee came with the factory tow package, I would guess you have blown fuses for the tow package turn signals and brake lights. Typically, you will have one fuse for the tow package or trailer left turn signal and brake light and one fuse for the right turn signal and brake light. I recommend checking your owners manual or fuse box legend to locate the tow package fuses and look for blown fuses. This should solve your problem without having to install a separate...
  view full answer...
• What is the Converter Box Used for on a 1998 Jeep Grand Cherokee
  The converter box included with the vehicle wiring harnesses for this vehicle will avoid overloading the vehicle's electrical system. The converter box does this by drawing power directly from vehicle's battery as opposed to from each individual light circuit. For your 1998 Jeep Grand Cherokee, I recommend using the Curt T-Connector Vehicle Wiring Harness part # C55349 if you do not have the factory tow package or part # C55260 if you do have the factory tow package.
  view full answer...
• Trailer Wiring Recommendation for 1994 Jeep Grand Cherokee
  For trailer wiring confirmed to fit the 1994 model Jeep Grand Cherokee as long as it was made after 1994 you would want the # 118349. If you have an older model you instead would want the # 46255.
  view full answer...
• Trailer Wiring Recommendation for a 1997 Jeep Grand Cherokee
  For your 1997 Jeep Grand Cherokee with a factory 4-way the correct replacement 4-way would be the part # C55260. The price is available at the attached link.
  view full answer...
• Where Does Factory Brake Controller Wire Terminate on a 1995 Jeep Grand Cherokee
  If your 1995 Jeep Grand Cherokee came with a factory installed 7-Way trailer connector then the wire for electric brakes is usually a green wire behind the driver's side kick panel. But regardless of what color it is the wire terminates at the 7-Way already. If you determine that the wire you found is not the correct wire or cannot find the correct wire then you can run your own wire, # 10-1-1 sold by the foot, from the brake controller to the back of the 7-Way and install it in the 7...
  view full answer...
• Trailer Light Turn Signal Does Not Work With Curt C55774 7-Way
  Thank you very much for your purchase from etrailer of the Curt T-Connector Vehicle Wiring Harness - 7-Way and 4-Pole Flat Connectors # C55774 for your 2015 Jeep Grand Cherokee with the factory tow package. There are a number of troubleshooting steps you can take to try and find the issue since your trailer's turn light signal is not working. in order to determine the specific problem you will need to purchase a circuit tester if you do not have one - the very handy Cordless Circuit Tester...
  view full answer...
• Trailer Wiring Recommendation for a 1998 Jeep Grand Cherokee Laredo
  The final authority on whether or not a vehicle had a tow package would be a Jeep dealer for your 1998 Jeep Grand Cherokee. Or, you can see if your vehicle has the connector behind the rear scuff panel in the rear cargo area and then test it with a circuit tester like part # 3808 to determine if it is active. For more info on where this connector is check out the installation instructions I attached to the right for the # C55260. If it's there then the # C55260 would work as a wiring harness. Now...
  view full answer...
• Power Reaching Trailer Wiring Converter But No Power On 4-Way on a 1997 Jeep Grand Cherokee
  First, the Curt trailer wiring harness # C55260, is designed to fit if the 1997 Jeep Grand Cherokee came with the factory tow package. If yours does not have the factory tow package that could be the issue. There could also be some fuses or relays related to the factory tow package wiring, if you have it, that are missing or blown. On some vehicles, power can get through if there is a relay missing but the full power cannot go through the converter until said relay is replaced. Use the...
  view full answer...
• Adapter to go From 7-Way on Vehicle to 4-Way on Trailer
  If I'm understanding correctly, you want to switch your Jeep's 7-way to a 4-way, but if you already have a 7-way on your Jeep, you can't switch it to the Curt 4-Way # C55260. You can still use a 4-way though, you'll just need a simple adapter: - 7-Way RV to 4-Way Flat Trailer Connector Adapter # HM47365 All you have to do is plug the # HM47365 into the 7-way on your Jeep, and it has a 4-way connector on the other end that you can plug a trailer 4-way into.
  view full answer...
• Parts Needed to Add Brakes to a Tandem 3,500 lb Axle Trailer to Tow with a 1996 Jeep Grand Cherokee
  It sounds like you currently have a wheel hub that has a 5 on 4-1/2" bolt pattern (taken from the far end of one bolt to the center of one directly across from it) and that you already have a brake mounting flange on two 3,500 lb axles. If this is the case then I recommend using the electric brake kit # AKEBRK-35-SA along with the Trailer Hub and Drum Assembly # AKHD-545-35-K. Electric brakes are the easiest to install and maintain so these will work out great for you. Just make sure that...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?