License Plate Bracket Needed for 23x47 Carpod Walled Cargo Carrier

Question

Question:

I have a 2017 Itasca Navion RV. This will obscure the license plate. Do you have a suggestion for mounting the plate on the rear of this holder?

asked by: Robert K

1

Helpful Expert Reply:

We do have license plate brackets like part # LP10SB that you could use to move your license plate so it sits behind the 23x47 Carpod Walled Cargo Carrier # M2205-2201. If you plan on driving at night time you should make sure to have a bracket with a light like part # PM436B. If you go this route then you will also need a wiring harness like part # HM38134 (you will connect the wire from the light to the brown wire and then cap off the additional wires for this application). Butt connectors like part # DW05744-5 are needed to connect your wiring.

Mounting the bracket can be a bit tricky as you don't have much wall space on that carrier. You could potentially secure it with zip ties but I'm not sure how durable that will be.

expert reply by: Jon G

1

Answer 1

I spoke with Yakima, and they said that the Replacement Lid Support for Yakima Cargo Boxes #8880684 and the Replacement Lid Support for Yakima Cargo Boxes #8880683 are the essentially the same thing minus the spring color, oddly enough. But, even…

view full answer...

Answer 2

The recommended cargo bag for the Carpod Carrier part #M2205-2201 that you referenced is the Carpod Bag part #M2202. This bag is specifically designed to fit the inner dimensions of the #M2205-2201 so it would be the best choice. This bag is weather…

view full answer...

Answer 3

There isn't a latch in the middle for you to lock like you'd typically see with a cargo box, but you could use some padlocks to prevent someone from opening the lid of the 23x47 Carpod Walled Cargo Carrier w/ Lid #M2205-2201. That being said,…

view full answer...

Answer 4

Hey Brian, Since you're needing 48 x 24 space for the pens, I recommend going with the Reese Solo Cargo Carrier #PS1040100 as opposed to the Inno Quick Base #IN92RR you were looking at. The Reese carrier has a tray measuring 32x48 so it will be…

view full answer...

Answer 5

Hello Sherri. No, the 24x60 Reese Cargo Carrier with etrailer Enclosure Cage for 2" Hitches - Steel - 440 lbs #RP85AR can not be folded up when it is not in use. The cage portion of the unit can be easily removed by loosening the 4 bolts on each…

view full answer...

Answer 6

Hi Bob; the inside dimensions of the #e82FV are going to match up to the cargo carrier you install it on. Since this is designed for 24" x 60" cargo carriers that will be the inside width and depth once it is tightened down on the carrier.…

view full answer...

Answer 7

Hi Jon; the actual width of the #IN94MR cargo box is 63-1/2". The full outside dimensions are 63-1/2" long x 28" wide x 15-3/4" tall and the inside dimensions are 57" x 23-1/2" x 14-3/4". The 39" measurement…

view full answer...

Answer 8

Hey Ramiro, thanks for reaching out! The 24x84 etrailer Enclosed Cargo Carrier for RV Bumper #e94VV weighs in at 185.60 lbs.

view full answer...

Answer 9

Hey Matt, so the etrailer enclosed carrier part #e54VV does tilt back with the hinge that is built into the shank of the carrier. Jeep Wranglers have rear doors that swing out so I would not anticipate this being able to tilt enough to fully allow…

view full answer...

License Plate Bracket Needed for 23x47 Carpod Walled Cargo Carrier

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching