Replacement Lead Leg for Venture 5th Wheel RV Landing Gear

Ask the Experts about this Lippert Components Accessories and Parts

Do you have a question about this Accessories and Part?

• Replacement Lead Leg for Landing Gear on 2010 Open Range M-337RLS 5th Wheel Trailer
  
• It sounds like you need a replacement driver leg for the landing gear on your 2010 Open Range M-337RLS 5th wheel trailer. The driver/lead leg is the one with the motor and gearbox attached; the other leg is called the follow leg. Replacement driver legs are shown on the linked page. You will want to try to find a manufacturer name and/or part number on the original jack leg if you can since this will simplify identifying the replacement. One of the most commonly used legs is part # LG-179013...
  view full answer...


• Repair Kit for Venture VMC900R Lead Leg Which Will not Move
  
• If the pin on the lead leg of your Venture VMC900R is sheared, you would need to use Lead Jack Repair Kit # LG-146059. Should you wind up needing a new leg, you would only need to measure the outside tube; I've added a photo showing you the length of the outer tube of Replacement Lead Leg # LC119102, which is what you'd need to measure. That would be the correct replacement for your landing gear if your current leg was 29-1/2". If it measured 33-1/2" you'd want to use Replacement Lead Leg...
  view full answer...


• What is the Difference Between Landing Gear Lead Legs # LC119102 and # LG-179013
  
• Landing gear lead leg # LC119102 has bracket stops places on the opposite side of the shaft. Lead leg # LG-179013 is a universal option and has bracket stops on both sides. So if you want you can use the universal leg.
  view full answer...


• Replacement Lead Landing Gear Leg for a 2004 Keystone Challenger 34TBH
  
• Replacement leg # LC178653 is unique to the Keystone Montana. Your 2004 Keystone Challenger likely uses a different lead leg, # LC179013. But it will depend on where the stops are located on the existing leg. The stops are the protrusions that stick out from the legs. Leg # LC179013 has then on the same side as the drive shaft, see picture. If yours are on the opposite side as what is shown in the picture you would need leg # LC119102.
  view full answer...


• Replacement Lead Landing Gear Leg Recommendation for Trailer with Leg Marked VMC900R
  
• Essentially the two jack legs are the same and either would work. Since the price is better the one I would go with is the part # LG-179013 which is the 29-1/2 inch length that you need.
  view full answer...


• Replacement Legs for Venture VMC900R Landing Gear
  
• If the thrust bearing is broken on your VMC900R Venture landing gear you are going to need to replace the leg, which you would need to match by the length of the outer tube, which is likely going to be 29-1/2 inches, but please measure to verify. Should that be the correct length you need # LC119102 for the lead leg or # LG-179014 for the follow leg.
  view full answer...


• Venture Landing Gear Repair Kit or Replacement Lead Leg
  
• It sounds like your Venture landing gear is not working properly on the lead leg. I recommend the Lippert Components Venture Lead Leg Repair Kit for 5th Wheel RV Landing Gear # LC146059 if you want to fix the internal gears. If you are looking for the replacement lead leg, you will want the Replacement Lead Leg for Venture 5th Wheel RV Landing Gear # LC119102.
  view full answer...


• Replacement Part Availability for Venture VMC900L Landing Gear
  
• The internal parts (screw and nut) on your Venture landing gear are not available as replacement parts but we may have a replacement leg. We carry several legs that could potentially work. Lead: # LC119102 (outer tube is 29-1/2 inches overall) Follow: # LG-179014 (outer tube is 29-1/2 inches overall) If these match what you have then replacing the leg is the way to go.
  view full answer...


• Lead Leg Replacement or Repair for 2008 Crossroads Cruiser 29CK 5th Wheel Landing Gear
  
• It is very likely that you have the Venture landing gear with your Venture labeled motor. The gearbox is obviously working because the follow leg is working, so I recommend repairing the lead leg with # LG-146059 or replacing the lead leg with # LC119102. You can double check the fit by measuring the outer tube with press fitted cap which will be 29-1/2 inches. If you get a different measurement of 33-1/2 inches then you will use the replacement leg # LG-177202.
  view full answer...


• What Is The Difference Between A Lead Leg And A Follow Leg With Landing Gear?
  
• The lead leg of your landing gear is the leg that has the motor and gear box attached to it directly. The follow leg has a connecting bar that is attached to it from the lead leg to move at the same rate as the lead leg. The follow leg does not attach to the motor assembly and gear box directly.
  view full answer...


• Dual Motor Replacement Powered Landing Gear Recommendation for Venture Kit
  
• For a system that has a 10,000 lb lift capacity, I recommend the Bulldog Electric 5th Wheel Landing Gear Set, part # BD500161. This landing gear features 36 inches of travel and will bolt right up in place of your Venture landing gear.
  view full answer...


• 2005 KZ Escalade Replacement Landing Gear Leg for Venture Independent Motor System
  
• The Replacement Lead Leg for Venture 5th Wheel RV Landing Gear # LC119102 is what you need. You can simply reconnect your motor/gearbox and utilize you independent electric leg. If your 2005 KZ Escalade trailer has top mounted motors instead, you will want the Replacement Lower Leg Assembly for Ultra-Fab Deluxe Electric Landing Gear Set # UF17-766004.
  view full answer...


• Will Venture Landing Gear Motor Fit etrailer Landing Gear
  
• The etrailer Landing Gear Set # RVLG-8000 that you referenced is designed to work with the motor kit # M1230 which has a slightly different design than your Venture motors. If you were wanting to retain the use of your current motors then we have the Venture Lead Leg # LC119102 and the Gearbox # LC276602 which you should be able to use with both motors for a dual setup. This lead leg has the same weld stops measuring 17-1/2" outside to outside as the etrailer landing gear you referenced.
  view full answer...


• Venture M-9000-PK Landing Leg Replacements
  
• The replacement lead leg for Venture landing gear is part # LC119102. The follow leg would be # LG-177201.
  view full answer...


• Replacement Lead Leg for Venture 5th Wheel Landing Gear
  
• Lippert makes about 90-percent of the trailer frames in the U.S. and also produces accessory items like landing gear for their OEM business and under other brands like Stromberg Carlson and Venture. You'll just want to verify the length of the outer tube on your landing gear lead leg. If the outer tube is 291/2-inches then use part # LC119102. If it is instead 33-1/2-inches long then use part # LG-177202. If your leg's outer tube is another length please advise.
  view full answer...


• Can a Single Motor Venture Landing Gear Set be Converted to a Dual Motor System
  
• To make the single motor landing gear into a dual-powered landing gear you will need to replace the existing follower leg with a lead leg # LC119102, add a new gear box LC276602, motor # LC142178, and switch # LC145236. It would be easier and cost less to just replace the whole system with a dual motor system such as # UF17-943010 rated for 12,000 pounds.
  view full answer...


• Replacement Lead Leg Recommendation for Landing Gear part # VMC900R
  
• The vmc900r part number is as Lippert style of landing gear. Which if that is what you have you'd want the part # LC119102 as a replacement lead leg since it sounds like yours is damaged beyond repair.
  view full answer...


• Replacement Lead Leg for Landing Gear
  
• Lippert landing gear parts are sold under other brand names as well, such as Stromberg Carlson, Venture and Atwood, and often an alternate part fits and works perfectly well. You'll just want to match the length of the original lead/driver leg's outer tube to the replacements we have, all shown on the linked page. If your motorized lead jack outer tube is 29-1/2-inches then part # LC119102 is perfectly suitable.
  view full answer...


• Replacement Fifth Wheel Lead Landing Gear Leg for Vmc900r-290032
  
• The Replacement Lead Leg for Venture 5th Wheel RV Landing Gear part # LC119102 will be the one you want. The outer tube of the jack measures 29-1/2" and offers up to 71" of extension.
  view full answer...


• Replacement Leg for Venture Landing Gear
  
• You did not mention which leg you needed but we do carry # LC119102 if you need the the Lead Leg or # LG-179014 for the follow leg. These will only work if your outer tube is 29-1/2 inches so you do need to measure to ensure that is what the leg you are replacing measures.
  view full answer...


• Replacement Landing Gear Lead Leg for Venture Landing Gear on a 2008 Komfort 5th Wheel Trailer
  
• You have Venture landing gear on your 2008 Komfort 5th wheel trailer. Lippert landing gear lead leg # LC119102 can be used on your trailer if the measurements match up to what you need. The outer tube on this leg is 29-1/2 inches (including the cap). If your leg's outer tube has a different measurement let me know what it is.
  view full answer...


• Replacement 5th Wheel Lead Landing Gear Leg for Venture 119102
  
• The correct replacement lead landing gear leg to replace your damaged Venture 119102 would be the # LC119102 from Lippert. Lippert manufactured landing gear for Venture, so this would be the correct replacement. If you're needing a replacement motor, it's part # LC142178.
  view full answer...


• Replacement Lead Leg for Landing Gear on 2010 Keystone Montana
  
• The correct lead leg for the landing gear model VMC900R on your 2010 Keystone Montana is Replacement Lead Leg for Venture 5th Wheel RV Landing Gear # LC119102. The price for this part can be found on the product page.
  view full answer...


• Replacement Landing Gear Legs for Venture Landing Gear VMC900R-227194
  
• The landing gear set you have is a very popular set by the brand Venture, for a replacement lead leg you'd want the part # LC119102 or for a replacement follow leg you'd want the # LC119101. The lead leg is the leg that the landing gear handle attaches to and the follow leg is the one opposite of that.
  view full answer...


• Venture Landing Gear Box Replacement Recommendation
  
• What you described does sound like a damaged gear box. This is pretty common for Venture landing gears like what you said you have and the correct solution is a new gear box which the part # LC276602 is the correct replacement for. For a replacement leg we have the part # LC119102 which has a retracted height of 33-3/4 inches and an extended height of 71 inches.
  view full answer...


• Replacement Lead Leg for Motorized 5th Wheel Landing Gear on 2017 Cherokee Limited 255RR
  
• Many 5th wheel landing gear parts are indeed interchangeable and it is not uncommon to find multiple items, and at different prices, that all appear to be a correct fit. Branding is not critical in this instance; matching the leg dimensions is what matters. We do not offer just the inside part of the leg but we do have both lead/driver legs as well as follow legs. Since you need the part on the motorized side you will want a replacement lead leg, all of which are shown on the linked...
  view full answer...


• What Would Cause RV Landing Gear Legs to Raise/Lower in Opposite Directions
  
• You have the second jack connected backwards most likely. You'll need to rotate the jack leg 180 degrees so that when the shaft of it turns it will work in the same direction as the lead leg.
  view full answer...


• Can a Lead Leg for Venture 5th Wheel Be Turned Into a Follow Leg?
  
• Because the two types of legs are oriented to be used on particular sides of the trailer, you're not going to be able to use a lead leg like the Replacement Lead Leg for Venture 5th Wheel Landing Gear # LC119102 as a follow leg. You may be possible to modify the leg and make it work, but I cannot recommend doing this. Because of this, you'll need to replace your follow leg with a specific matching follow leg for your landing gear system. The matching landing gear follow leg for the lead...
  view full answer...

Do you have a question about this Accessories and Part?