What Size Wrench is Needed for a 2" Hitch Ball with 1 Inch Diameter Shank

Question

Question:

The nut size is 1.5inch yet the info states Requires socket size: 1-7/8. Should I not need a 1.5inch socket as 1 7/8inch is too large? Thanks

asked by: Jimmie

0

Expert Reply:

You will need a 1-1/2" wrench like part # C20001 in order to install the nut on the 2" Hitch Ball part # 63845. A 1-7/8" wrench would be much too large.

expert reply by: Conner L

0

Answer 1

You can have a 2-5/16 inch hitch ball on either a 1 inch or 1-1/4 inch shank. The nut on a hitch ball with a 1-1/4 inch shank takes a wrench with a 1-7/8 inch socket. A hitch ball with a 1 inch shank will take a wrench with a 1-1/2 inch socket. You…

view full answer...

Answer 2

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 3

Hey Delbert, thanks for reaching out! Yes, the Andersen Weight Distribution Hitch w Sway Control #AN53VR can be used for a lighter trailer like what you have. You'll just need to adjust the system to accommodate your weight and you'll be good…

view full answer...

Answer 4

Hi Emily, Before buying anything you'll want to verify that both the Pilot and the trailer hitch installed on it are rated for use with a weight distribution hitch (WDH). From what I can see Honda does not recommend it because it can shift the…

view full answer...

Answer 5

Curt hitch ball #40038 has a 1 inch diameter shank. For Curt balls with 3/4 or 1 inch diameter shanks you would use wrench #C20001. The nut on that ball should use the 1-1/2 inch end of the wrench. You could also use a large crescent wrench if you…

view full answer...

Answer 6

Hey there Michelle! While weight distribution systems are supposed to get the truck and trailer as level as possible, they are not complete miracle workers and won't make both 100% level in all situations. In fact, Andersen has a section of the…

view full answer...

Answer 7

Good morning Hurley (cool name by the way. I like the clothing brand Hurley). Also, congrats on the new-to-you Chevy! That is an excellent question that comes up from time to time on various vehicles and weight distribution systems. So on your 2023…

view full answer...

Answer 8

Hey there Layla! There are a few different forms of weight distribution hitches, but the majority of the systems that have sway control use friction bars, which work similar to brake pads on your vehicle. This works really well, but it can sometimes…

view full answer...

Answer 9

I checked with Aluma and they list a 14" Liger Wheel and Tire 60-0001396 as a replacement 14" wheel for their trailers but they do not specify the finish. We do have one 14" Liger Wheel item #LH84FR. It is gunmetal gray and has a 5 on…

view full answer...

Answer 10

For a 6 inch drop ball mount that is aluminum we have the Curt Ball Mount for 2" Hitches - 5" Rise, 6" Drop - 8,000 lbs - Aluminum #C24WR which would work well for you. It has a 8,000 lb capacity and weighs a total of 5 lbs. I attached…

view full answer...

Answer 11

Hey Stanford, do you have a 1-15/16 inch wrench? That would be the correct size based on the measurement you took for the nut of the #TS27VR.

view full answer...

Answer 12

Oh it won't stand up well to an angle grinder at all. The Trimax Heavy Duty Adjustable Wheel Lock item #TMX42ZR is designed to stop the casual thief with bolt cutters. Not a dedicated criminal with power tools. I am sorry but I do not have…

view full answer...

What Size Wrench is Needed for a 2" Hitch Ball with 1 Inch Diameter Shank

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching