Trailer Hitch Fit Options for 2007 or 2011 Toyota Camry XLE w/ Dual Exhuast

Question

Question:

I am about to buy either a 2011 Camry XLE or a 2007 Camry XLE. These cars have dual exhausts. Is there a Class II hitch available for either of these cars?

asked by: Joe

0

Expert Reply:

I checked with my contacts at Hidden Hitch, Draw-Tite and Curt, regarding the fit of the Curt # C12343, the Hidden Hitch # 90152 (no longer available) and Draw-Tite # 36416 Class II trailer hitches on your 2011 Camry. There would be absolutely no fit issue or interference with the dual exhaust. These hitches are compatible the 2007-2011 Camrys, so they'll work with either vehicle you referenced.

I'd recommend the Draw-Tite model, unless you were planning on towing with the hitch, in which case I'd go with the Hidden Hitch model which includes a ball mount.

For towing, you'd also need the trailer wiring harness. For the 2007 model, you'd need the # 118405 or for the 2011, use part # 118482. For a 2 inch trailer ball, use part # 19258 or part # 19256 for a 1-7/8 inch ball.

I've linked you to install videos for the part's I've mentioned.

expert reply by: Mike L

0

Answer 1

For a 2013 Camry, you'd want to use the Draw-Tite Class II, part #36540. This hitch will fit a vehicle with a dual exhaust. The #36416 hitch you referred to is a fit for the 2007-2011 Camry, so it won't fit your 2013 model.

view full answer...

Answer 2

On the 2009 Toyota Camry, all of the hitches available are Class II 1-1/4 inch hitch openings. The hitches will have a 3,500 lb. Gross Towing Weight and a 300 lb. or 350 lb. Tongue Weight. There is not a 2 inch hitch available for your vehicle,…

view full answer...

Answer 3

Yes, the Draw-Tite Class II Trailer Hitch, part number 36416, will fit your 2008 Toyota Camry SE. You will need a drawbar and a properly sized hitch ball along with a wiring harness to complete your towing setup. The Class II Drawbar 2-5/8" Rise…

view full answer...

Answer 4

It looks like the brake light and running light wires on harness #118405 plug into the same location on a 2009 Toyota Camry. Check the converter wiring going into the converter to see if power is at that point since it is already at the tail light.…

view full answer...

Answer 5

The Hidden Hitch, part #90152 (no longer available), and the Draw-Tite, part #36416 are essentially the same hitches. Draw-Tite and Hidden Hitch are sister companies and these hitches were probably built using the same jigs. The difference is, as you…

view full answer...

Answer 6

Hey Richard, for your 2011 Toyota Camry LE V6 with the dual exhaust, I actually recommend the Draw-Tite Hitch #36416. This hitch was designed with the dual exhaust models in mind, and we have had many customers report back to us that it will fit the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Trailer Hitch Fit Options for 2007 or 2011 Toyota Camry XLE w/ Dual Exhuast

Featured Help Information

Miscellaneous Media

Continue Researching