Wiring Needed to Add Third Brake Light Wiring for Topper Installed on 2026 Ford Maverick
Updated 09/21/2026 | Published 09/16/2026 >
Question:
Looking to wire up a 3rd brake light in my topper. It just has the wires to the brake light nothing additional. I have a 2026 Ford Maverick Lariat with the 4k tow package. What is the best set of products to get the brake signal to that light? C55384, C59DR are two options i was looking at. Would PP20-702 be required? Thanks!
asked by: Tanner B
Expert Reply:
Hey Tanner, you mentioned a few part numbers but all you would really need is the part # PP20-702 to get that dedicated third brake light signal for the topper and your 2026 Ford Maverick. You would just need to wire that to your taillight wiring and you'd have the correct signal.

Phillip
9/19/2026
Could never get 2021 F150 happy with anything other than a dedicated relay driven off the ford dedicated line meant for this purpose. In other words Ford dropped the ball. Their lead provides the brake light voltage, but not the currrent to drive it....hence the need for a dedicated relay. Ford dealership couldnt do it....I figured it out. Its stupid and i blame it all squarely on fords stupid , overly complicated battery management system. No such thing as no splicing.


Joe
9/19/2026
Doesn’t work on trucks which have cam bus systems


Phil
9/19/2026
Added to a 2000 Ford F350 by splicing into 4 flat connector so I can take off canopy when I want to. Works great but note it says it doesn’t work with LED. Not an issue for me but don’t know on Maverick


Bruce A.
9/19/2026
I added the the trailer wiring extension harness with the 4 pin connector . I wired in the third brake modulator into the harness . PP30-702 . You need this . You will need some black electrical tape or shrink tubing . Does not come with the kit . I used an extension wiring like you posted because I didn’t want to cut my factory wiring . Since you have the towing package . Most likely you will want the big black connector . I also added a third brake modulator into got on Amazon . You will also want to add connectors somewhere between the topper and truck bed in case you have to remove the topper . I did all this on my GMC Sierra with topper . Works great .

Product Page this Question was Asked From
Featured Help Information
Instructions
Continue Researching
- Shop: Truck Topper
- Shop: Duracap Quest Truck Topper - Aluminum - Black - Hard Camper Shell
- Shop: Trailer Wiring
- Shop: 3rd Brake Light Logic Module
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Shop: Suspension Enhancement
- Search Results: trailer tires and wheels
- Article: How to Measure for Trailer Hitch Drop
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Search Results: trailer jack
- Shop: Brake Controller
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Search Results: trailer hitch ball mount
- Shop: Base Plate for Tow Bar


Tanner B.
9/17/2026
I was hoping for no wire splicing.