Placement of Camper Packer and Can It Be Cut Shorter
Updated 05/06/2026 | Published 04/28/2026
Question:
Where should I place the forklift camper packet on my host mammoth 11.6 camper it weight about 5000 lbs. The height of 35 inchs also seems really tall to store the camper. So why is it so tall and would it be better to cut it down and if so what height would be better. Thank you for your expert advice!
asked by: Steven D
Expert Reply:
Hello again Steven. The Camper Packer # TLA7010 is meant to support the camper under the main floor/frame structure, not out at the edges. You’ll use 2 stands, one toward the front and one toward the rear. We don’t have a specific placement for a Mammoth 11.6, so if you’re unsure, it’s a good idea to check with Host Industries for the best support points.
As for height, the 30"–35" range is intentional since that’s about where most truck beds sit, so it reduces how far you have to lift the camper when loading. You can cut the lumber shorter if you want it lower for storage, just keep in mind you’ll have to lift it higher to get it back on the truck.
(click to enlarge)
Product Page this Question was Asked From
TorkLift Camper Packer Camper Stand Kit
- Accessories and Parts
- Camper Jacks
- Camper Stand
- TorkLift
more information >
Continue Researching
- Shop: Trailer Hitch
- Shop: TorkLift Camper Packer Camper Stand Kit
- Video: In-Depth Review of the TorkLift Camper Packer Camper Stand Kit
- Search Results: truck camper supports
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: Will 2019 Ford F-450 Require New Rear Tie-Downs Installing TorkLift Hitch
- Q&A: How Is TorkLift SuperTruss Hitch Extension Length Measured
- Video: How to Install the TorkLift SuperHitch Magnum Trailer Hitch Receiver on a 2021 Ford F-450 Super Duty
- Shop: Factory Mount Installation Kit for BedSlide S and Classic - No Drill
- Shop: TorkLift Wobble Stopper Camper Jack Stabilizers w/ Locking FastGun Handles - Round Jacks - Qty 2
- Shop: TorkLift SuperHitch Magnum Trailer Hitch Receiver - Custom Fit - Class V - 2-1/2" and 2"
- Video: Mount: Curt Trailer Hitch Receiver on a 2023 Ford Edge
- Shop: Vehicle Sway Bars
- Shop: Hellwig Adjustable Big Wig Rear Anti-Sway Bar - 1-5/16" Diameter
- Shop: TorkLift SuperTruss Hitch Extension for SuperHitch Trailer Hitch Receivers - 36" Long
- Q&A: 2024 Ford F-350 Super Duty TorkLift SuperHitch and SuperTruss Recommendations for In-Bed Camper
- Shop: Camper Tie-Downs
- Video: DIY Install: Curt Trailer Hitch Receiver on your 2019 Ford Edge
- Search Results: propane hoses
- Search Results: tire pressure monitoring
- Search Results: camper jacks accessories and parts
- Search Results: propane accessories
- Search Results: dual 20 lb tanks propane accessories
- Q&A: Recommended Replacement Pigtail Hoses To Go From Propane Tank to Regulator On 5TH Wheel RV Camper
- Q&A: How to Remove and Reinstall Push to Connect Air Fittings
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Video: How to Choose a Trailer Brake Controller
- Shop: Trailer Wiring
on Accessories and Parts
Steve
5/6/2026
I cut my lumber down to make the camper packer a total height of 29 inches. I am more comfortable with this height and Robin at etrailer was a great help and another associate also contacted the manufacturer of the camper packer to reassure me I was not making a mistake. The camper is very stable at this height.