Replacement Lug Nuts for a 2021 Grand Design Imagine XLS 17mke

Question

Question:

I’m looking for sold one piece lug nuts that will fit a 2021 grand design imagine xls 17mke

asked by: Chuck M

1

Helpful Expert Reply:

Welcome back Chuck! The Americana Trailer Wheel Lug Nut item # AM26NR is exactly what you'll need to replace the ones on your 2021 Grand Design Imagine XLS 17mke. This stainless steel lug nut fits 1/2" wheel bolts with 20 threads per inch just like the ones that came from the factory. It is a 3/4" hex bolt size with an overall length of 1-1/2".

The Americana Trailer Wheel Lug Nut item # AM26NR is sold individually. It will work great with the Aluminum Eagle Trailer Wheel item # LH89VR, you've been looking at. They will need to be torqued to 90-120 ft-lbs.

Did you damage one of your wheels?

You can add this information, along with any other questions you have, where it says Add Comment.

expert reply by: Jerred H

1

AM26NR
(click to enlarge)

Answer 1

Hey Chuck, thanks for the information! I checked with Grand Design and the closest comparable option we have for the rims that came with it are the Aluminum Eagle Trailer Wheel item #LH89VR. This a 14" rim that has a 5 on 4-1/2" bolt…

view full answer...

Answer 2

Hi Rusty; the Dexter #84546UC3-EZ and etrailer #AKHD-5475-35-K will both fit a 3,500 lb axle but they have different bolt patterns. You already ordered the Dexter in the past so I'm assuming your wheels are 5 on 4-1/2. For the same bolt pattern…

view full answer...

Answer 3

The most common lug nut socket sizes for trailers are as follows; 13/16", 7/8", 17mm, and 19mm. I would be willing to bet you need a 13/16" socket but in order to be sure you get the correct size you should consider the Telescoping Lug…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...