Looking For Replacement Grease Seals For 2019 Coachmen Chaparral 5th Wheel

Question

Question:

I have 5100 LB Dexter axles on my 2019 Coachman Chaparral 5th wheel. Do I need to remove the grease seals and measure them or is there an application chart I cannot find ? Thank You

asked by: Ned G

0

Expert Reply:

Hey Ned, thanks for reaching out. There isn't an application chart for grease seals, but we see a ton of these Dexter 5,100 lb axles here at our shop and they all use the same seal size. So, what you'll need for your axle is the following:

- Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL # GS-2250DL

A Dexter 5,100 lb axle is basically just a standard 5,200 lb axle that's been de-rated because of the overhang of the camper.

Are you needing just the seals? Or are you looking for a full bearing kit?

expert reply by: Jesse M

0

Grease Seal - Double Lip - 2.250" ID - 3.376" OD - GS-2250DL
(click to enlarge)

Sharon

4/10/2026

Perfect fit as always the best customer service too

Jesse M.

4/13/2026

@Sharon I appreciate that, Sharon. Thanks for sharing!

George M.

4/10/2026

I used this seal on my 24’ enclosed trailer with 5200# axles. Installed nice and haven’t had any issues. I’ll buy them again.

Jesse M.

4/13/2026

@GeorgeM Nice! Glad to hear the new seal is working out. Thanks for sharing!

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Looking For Replacement Grease Seals For 2019 Coachmen Chaparral 5th Wheel

Product Page this Question was Asked From

Continue Researching