Will The Curt Hitch C23FR Fit A 2022 Ford Escape Hybrid?

Question

Question:

I’d like to make sure before I purchase that the etrailer hitches recommended for a 2022 Ford Escape Hybrid actually fit a Hybrid model. There seems to be contra statement in the info that says it’s not for Hybrid or PHEV models. If it does fit a Hybrid are there additional special installation steps needed to accommodate the battery being in the back? Thank-you!

asked by: Russell A

0

Expert Reply:

Hi Russell!

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C23FR will fit standard and Hybrid versions of the 2022 For Escape, but not the PHEV. For that we have the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C67MJ.

With that being said, I am not seeing that anything special needs to be done to accommodate the hybrid battery. You will need to enlarge a few holes in the frame, but other than that, it basically bolts right up.

What are you wanting the hitch for?

expert reply by: Lazer S

0

Curt C23FR Ford Escape
(click to enlarge)

Lazer S.

10/22/2025

Hey Russell, how did the hitch install go on your Escape Hybrid? It sounds like the fit should have been straightforward once the frame holes were enlarged. Sharing how it turned out could help others with the same model.

Russell A.

10/22/2025

Lazer, I responded to a email and submitted a review on both items Sunday evening. Specific comments are in there. Some minor surprises but the install was successful.

Lazer S.

10/22/2025

@RussellA Nice! I just saw them. Sorry you had some surprises, but I'm glad everything is installed and ready for use! I wasn't aware of that heat shield and I will see if I can get that added to a tech tip on the hitch. So thanks for that! ^___^ Little surprised about the wiring though. Tekonsha is usually very good about having enough (or more than enough) excess wiring to mount everything. Did you run it in a unique way by chance?

Answer 1

Hey Richard, for your 2023 Lincoln Corsair we only have universal style trailer wiring kits like the #119147KIT as there aren't any plug and play style harnesses available at this time.

view full answer...

Answer 2

Hey Joe, thanks for reaching out! I don't have a way to get those measurements, but what I can say is that Curt made the Trailer Hitch Receiver #C67MJ and has it listed as a custom fit for your 2024 Ford Escape PHEV so you can be confident it…

view full answer...

Answer 3

To install the etrailer brand #e89YR Class III hitch on your 2021 Ford Escape, you will NOT need to trim the bumper fascia, as you can see in the provided photo and video showing the identical Curt hitch being installed on a 2021 Ford Escape like…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Will The Curt Hitch C23FR Fit A 2022 Ford Escape Hybrid?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching