What Size Diameter Snap Ring Does the Pull Pin, Easy Swivel Trailer Jack with Foot DL22686 Fit?
Updated 09/04/2025 | Published 07/21/2025 >
Question:
Regarding DL22560. I would like to send pictures of my current set up and see if this jack is the correct jack for my boat trailer.
asked by: Brad M
Expert Reply:
Hey Brad. You can send any pictures you have directly to me at the address you receive this response from.
The Pull Pin, Easy Swivel Trailer Jack with Foot item # DL22686 fits a 2-1/4" diameter snap ring if your trailer already has a welded on mounting bracket.
What kind of boat trailer do you have?

Mark
9/3/2025
Hi, I have a bracket that's already welded on and would like to just replace the jack. The hole on the mounting bracket has a 2.5" exterior diameter and 2.25" interior. Ideally, I would like a jack with the crank on the side as the top mounted handle hits the tool box on the trailer. Can you recommend something that would fit those specs? Thanks! Mark


Product Page this Question was Asked From
Dutton-Lainson Pull Pin Swivel Trailer Jack w/ Foot - Sidewind - 10" Lift - 2,000 lbs
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- Side-Mount Jacks
- Swivel Jacks
- Sidewind Jack
- 1001 - 2000 lbs
- Manual Jack
- 10 Inch Lift
- Weld-On
- With Rectangle Foot
- Dutton-Lainson
more information >
Continue Researching
- Shop: Dutton-Lainson Pull Pin Swivel Trailer Jack w/ Foot - Sidewind - 10" Lift - 2,000 lbs
- Shop: Replacement Retaining Ring for etrailer and Ram Snap Ring Swivel Jacks
- Shop: REPL Snap Ring for Swivel Trailer Jacks - 2-5/16" Inner Diameter
- Shop: Round Snap Ring Swivel Trailer Jack w/ Footplate - Sidewind - 14-1/2" Lift - 2,000 lbs - Weld
- Q&A: Replacement Jack Compatible with Welded Jack Plate on Ranger Boat Trailer
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Shop: Power Mountain Tallboy Off-Road Bottle Jack - 8-1/2" to 37-3/4" Lift - 6 Tons
- Search Results: trailer wiring
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Q&A: Does etrailer Carry Furrion Chill Cube w/ Heat Pump to Replace Dometic Duo-Therm
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Search Results: trailer jack
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Shop: Base Plate for Tow Bar
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer lights


Jerred H.
7/29/2025
Thanks for the pictures and the measurements! Since your Atwood 500 lbs jack's mounting bracket has a snap ring with a 2" inside diameter you'll be good using the Pull Pin, Easy Swivel Trailer Jack with Foot item # DL22686 you were looking at. The outer diameter is probably 2-1/4" or close to it.