What JT Strongarm Kit Should I Get For My 5th Wheel With 54-1/4' Between Landing Gears
Updated 06/03/2025 | Published 05/26/2025
Products Featured in This Question
Question:
I have a fifth wheel with 54 1/4 inches between the front landing jacks. The rear jacks are electric piston jacks. Which JT strong arm kit should I buy?
asked by: John
Expert Reply:
Hey John,
Since you have less than 58" between those landing gears you will want to go with part # LC191024. This is a kit specifically for 5th wheels with a distance between landing gears less than 58". Along with that you will want to go with # LC314592 which are adapters that will be used for the electric/hydraulic ones in the rear. This has everything needed to install in the kit for you.
What trailer are you putting these on?
Product Page this Question was Asked From
JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ Less Than 58" Between Landing Gear
- Camper Jacks
- 5th Wheel Camper
- Stabilizer Jacks
- Steel
- Manual Jack
- 6 Jacks
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: x~chock
- Search Results: brace
- Search Results: sewer adapter pro
- Search Results: camco
- Search Results: smart plug
- Search Results: smartplug 50 amp
- Search Results: rhino rv sewer adapter pro
- Shop: Victron MultiPlus-II Pure Sine Wave Inverter Charger - 4,000 Watts - 95 Amps - 48V
- Q&A: Will MORryde X-Brace Stabilizers Fit A 5th Wheel Trailer With Round Tube Jacks
- Shop: JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ 58" or More Between Landing Gear
- Shop: MORryde X-Brace 5th Wheel Landing Gear Stabilizer
- Q&A: Recommended Smart Plug 50amp RV Power Cord to Work w/a 30 amp 240V Generator
- Shop: JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ Less Than 58" Between Landing Gear
- Shop: Victron Orion-Tr Smart Isolated DC-DC Charger w/ Bluetooth - 3-Stage Charging
- Shop: Hydraulic Jack Adapter Lugs for JT's Strong Arm Jack Stabilizer Kits - Qty 2
- Shop: Victron Lynx Shunt VE.Can with Built-In Battery Monitor - M10
- Q&A: Will King Pin Tripod Stabilizer or JT's Strong Arm Stabilizer Offer Better Support
- Shop: Trailer Wiring
- Shop: Fifth Wheel Hitch
- Q&A: JTs Strong Arm Jack Stabilizers for 5th Wheel Over Or Under 58 between landing Gear
- Q&A: Recommended Ways To Stabilize Bouncy 5th Wheel Trailer Other Than King Pin Stabilizer
- Video: Review of Lippert Camper Jacks - Stabilizer Jack - LC191023
- Video: Lippert JTs Strong Arm 5th Wheel RV Jack Stabilizer Kit Review
- Video: Ultra-Fab Chock and Lock Wheel Stabilizers Review
- Video: A Closer Look at the Super Grip Chock Wheel Stabilizers for Tandem-Axle Trailers and RVs
- Video: An In-Depth Look at the MORryde X-Factor Crossmember for Standard Frame Hangers
- Video: Set up: MORryde 5th Wheel Cross Brace Landing Gear Stabilizer on a 2018 Jayco Eagle Fifth Wheel
- Video: How to Install the Curt T-Connector Vehicle Wiring Harness on a 2022 Toyota Highlander
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
on Camper Jacks
John E.
6/1/2025
Nick, Thanks for your help. A question on the strong arm stabilizer for my rear jacks - On my rear jacks, there is a rectangular foot pad. But the holes they drilled in the round leg were not in line with the cross member. The inside face on the foot pad where I'll attach the strong arm is not in line with the cross member I'll mount the strong arm to. Not sure if this matters. But if it does, does Lippert have a round foot pad for a 2 inch round leg for my rear jacks