See what our Experts say about this Lippert Camper Jacks

• Recommended Stabilizing Kit for Lippert Auto Leveling System on 2017 Keystone Sprinter 5th Wheel
  The auto leveling system on your 2017 Keystone Sprinter is a Lippert auto leveling system, so the stabilizers that I recommend are the JT's Strong Arm Jack Stabilizer Kit which are also by Lippert and confirmed to work. If you have more than 58 inches between your front landing gear legs, then you will want part # LC191023. If you have less than 58 inches, then you will want part # LC191024. You will also need the Adapter Lug, # LC314592, for the rear leveling legs.
  view full answer...
• What JT Strongarm Kit Should I Get For My 5th Wheel With 54-1/4' Between Landing Gears
  Hey John, Since you have less than 58" between those landing gears you will want to go with part # LC191024. This is a kit specifically for 5th wheels with a distance between landing gears less than 58". Along with that you will want to go with # LC314592 which are adapters that will be used for the electric/hydraulic ones in the rear. This has everything needed to install in the kit for you. What trailer are you putting these on?
  view full answer...
• AC Unit And Stabilizers For My Keystone 2700bh Cougar
  Hey Matt, Looks like you are going for some upgrades! We have just what you need. Our inventory part number is different than the manufacturers. That unit that was recommended is actually our part # FR76PR, Furrion Chill 13,500 BTU AC unit. Now I know you are wanting to add a unit, are you wanting the new unit to tie into the existing system or stand alone? If you are able to send me the model of your original unit I can see if we have a replacement that will be able to tie into the...
  view full answer...
• Which JT's Strongarm Kit For Keystone Everest with 60 inches Between the Legs
  Hey Tony, I attached a link to the install instructions for the JT's Strong Arm part # LC191024 on this page. You will probably have to scroll down a bit to get to them but it will be under the helpful info heading. That said since you have 60 inches between your jack legs the correct kit you should have gone with is the part # LC191023.
  view full answer...
• Furrion AC Unit and JT's Strong Arm Stabilizer Kit for a Keystone 2700BH Cougar Sport
  Hey Matthew, thanks for reaching out! The Furrion Chill HE # FR76PR is the same as the part FACR13HESA-BL that you referenced - we just have our own part number for it. When it comes to choosing the correct JT's Strong Arm kit the breaking point is 58" for the distance between the landing gear. The Kit # LC191023 is for 58" or more between the landing gear, while the Kit # LC191024 is for less than 58" between the landing gear. The Timbren Kit # TFRTT350J will fit your truck, but is...
  view full answer...
• Is There a JTs Strongarm Stabilizer System that Fits Lippert Electric Stabilizers
  Hey Vernon, we have JTs Strongarm stabilizer kits that work with the Lippert Electric Leveling systems but you would need to get me the distance between the landing gear feet to pick out correct fit. The part # LC191023 is for if the distance is more than 58 inches or the part # LC191024 is for if the distance is less than 58 inches.
  view full answer...
• Stabilizers For Electric Automatic Landing Gear
  While we do have an option for you, MORryde has told us the MORryde 5th Wheel Cross Brace Landing Gear Stabilizer # MR72AR should not be used with auto leveling landing gear. So what you would need instead, that is confirmed to work with your electric auto leveling landing gear, is an option from Lippert, the JT's Strong Arm Jack Stabilizer Kit . The only thing you need to know for the right kit is the distance between the landing gear legs; you will also need an adapter for your electric...
  view full answer...
• JTs Strong Arm Jack Stabilizers for 5th Wheel Over Or Under 58 between landing Gear
  To determine which JT Strong Arm Stabalizer kit you need, just measure the distance between the inside edges of the landing gear feet. If it measures less than 58" then you need kit # LC191024. If it measures more than 58" you need kit # LC191023. These stabalizers install quickly with all neccessary hardware included. Once installed you need only to tighten the t-bolts when setting up camp. Between ease of use and the dramatic difference in unwanted trailer movement - these are a smart...
  view full answer...
  
• Can I Install The JT's Strong Arm Stabilization Kit On A Hydraulic Auto Leveling System?
  Tri Pods do give you a major boost in stabilization, but a system like the JT Strong Arm Stabilizer Kit # LC191025 will be much more stabilizing. Why? Well you are taking your current jack and adding two separate components, creating a larger spread compared to scissor jacks. Also creating two bigger triangles will result in more stabilization. So, the Strong Arm Jack Stabilization is the more stable route. If I were installing these arms, I would be using two of the adapter lugs # LC314592...
  view full answer...
• Product Comparison Of MORryder Scissor Jack Cross Brace And JTs Strong Arm Jack Stabilizer Kit
  The difference between the MORryde Scissor Jack Cross Brace Stabilizer for Trailers and RVs # MR82AR, and the JT's Strong Arm Jack Stabilizer Kit # LC191023 is while both limit side to side movement of your 30' travel trailer, only the JT will limit the front to back due it using 4 stabilizing arms on the front stabilizers. Neither the MORryde or the JT's will need to be removed from the trailer when you are ready to get back on the road. I recommend the JT's Stabilizer Kit, but to determine...
  view full answer...
• Will MORryde X-Brace Stabilizers Fit A 5th Wheel Trailer With Round Tube Jacks
  Hey Shane, Can you email me some pictures of your setup so I can see what you're working with? I'll send you a separate email to reply to. Update: Got your picture, unfortunately the MORryde 5th Wheel Cross Brace Landing Gear Stabilizer # MR72AR doesn't currently offer a mounting bracket to connect to your round leveling jacks. JT's Strong Arm Stabilizers have an adapter lug # LC314592 available that can mount to the footplate instead of the jack tube, allowing you to mount their...
  view full answer...
  
• Options for Stabilizing Fifth Wheel Automatic Leveling Jacks
  The JT's Strong Arm Stabilizer Kit # LC191023 paired with the either # LC314597 to adapt it to electric jacks, or # LC314592 to adapt it to hydraulic jacks, can be used with auto leveling jacks without issue. I spoke to MORryde and the # MR72AR said that this should not be used with hydraulic auto leveling jacks, unfortunately. That being said, they did say this will work with most electric auto leveling systems that use square jacks.. It should be noted, however, that the # LC191023...
  view full answer...
• Correct JT's Strong Arm Stabilizer Kit for 2019 Coachman Catalina 29TH
  For the correct JT's Strong Arm Jack Stabilizer Kit you'll need to measure the the distance between the landing gear on your 2019 Coachman Catalina 29TH. The cutoff is 58" for the 2 different models so you'll just have to choose from the following 2 options depending on what you're able to measure: Less Than 58 Inches - # LC191024 58 Inches or More - # LC191023 Attached is a photo to further demonstrate how you'll take the measurement. Unfortunately we don't have a list of the distances...
  view full answer...
  
• Adding Stabilization Jacks To Fifth Wheel Trailer That Uses Lippert 3.0 Ground Control
  Yes, you can add two stabilizer jacks to the long tail portion of your Sabra to help stabilize it along with your Lippert Ground Control part # LC675817. I recommend the pair of 2 Ultra-Fab Scissor Jacks part # UF48-979031 to add to the rear of the trailer. You probably do not have holes in the trailer frame at the rear of your trailer so you will most likely need to drill into the support brace of the trailer frame to attach the brackets of the jacks. I have attached an installation...
  view full answer...
  
• Can JT's Strong Arm Jack Stabilizer Kit be Used on Round Hydraulic Landing Gear Jacks
  Yes, the JT's Strong Arm Jack Stabilizer Kit # LC191023 referenced in your question can be used with hydraulic round jacks like what you have on your 2018 Grand Design as long as you add the Hydraulic Jack Adapter Lugs # LC314592. These adapter lugs can be welded or bolted onto the foot pads of your landing gear to allow the JT's Strong Arm stabilizers to attach to the jacks. The Strong Arm Kit you referenced is designed for trailers that have 58 inches or more between the front landing...
  view full answer...
• Recommended 5th Wheel Landing Gear Stabilizers For Round Tube Landing Gear Legs
  Hi Brian, The MORryde 5th Wheel Cross Brace Landing Gear Stabilizer # MR72AR mounting brackets require a square tube design in order to install so these braces won't be a fit for your round tube landing gears. Instead you'll need the JT's Strong Arm Jack Stabilizer Kit for 5th Wheel RVs w/ 58" or More Between Landing Gear # LC191023 or # LC191024 (Less Than 58" Between Landing Gear). In the video attached below Brad installed this system on a round tube system by using adapters # LC314592...
  view full answer...
• What is the Difference Between Lippert Components JTs Strong Arm LC191024 and LC191025
  Lippert Components JT's Strong Arm # LC191025 is designed for use with travel trailers whereas # LC191024 is designed for 5th wheel trailers with less than 58 inches between the landing gear jacks.
  view full answer...
• How To Find the Correct Replacement Landing Gear Legs for a 2013 Keystone Laredo
  In order to find the correct replacement landing gear legs for your 2013 Keystone Laredo 335TG I would need you to take two quick measurements of your existing landing gear legs, the outer tube length and weld stop spacing. I have attached a photo to assist. The most common replacement landing gear legs are the Replacement 5th Wheel RV Landing Gear Legs part # LC179013 for lead and part # LC179014 for follow. These measure 29-1/2" on the outer tube and 15-1/2" between the weld stops....
  view full answer...
  
• Determining The Correct JT's Strong Arm Stabilizer For A 2021 Grand Design Reflection 33RLS
  To determine which JT's Strong Arm Stabilizer would be the correct fit for your 2021 Grand Design Reflection 33RLS 5th wheel you would just need to measure the space between your two front landing gear legs. If you have less than 58" then you'll need part # LC191024, and for trailers with over 58" of space you'll need part # LC191023. I've attached a short video below where Brad will walk you through the installation process.
  view full answer...
• Can JT's Strong Arm Stabilizers be Used with Lippert 6-Point Landing Gear and Jack System
  Yes, you can use JT's Strong Arm Jack Stabilizer # LC191025 with the Ground Control or Level Up system on your trailer if you added the adapter lugs # LC314592. The adapter lugs are sold in quantities of 2. The JT's kit listed above is the travel trailer version. It looks like your trailer is a 5th wheel so you would need # LC191023 for a 5th wheel if the landing gear has 58 inches or more between the front jack legs. If less than 58 inches use # LC191024. One of the best items to stabilize...
  view full answer...
• Replacement Parts for JTs Strong Arm Jack Stabilizer
  We do have the T-bolts, # LC314594, and I believe you also need the shorter swing bolts, # LC314595. But I checked with Lippert and the actual Strong Arms are only available in the kits. For trailers over 58 inches between the landing gear you would use # LC191023. The model for travel trailers is # LC191025. The model for trailers under 58 inches between the landing gear use # LC191024.
  view full answer...
• Where Does the Front of the Lippert Components JT's Strong Arm Jack Stabilizer # LC191024 Attach to
  The front brackets of the Lippert Components JT's Strong Arm Jack Stabilizer # LC191024 that you referenced actually attach to either of the landing gear legs at the front of the trailer. You would not install them to the frame.
  view full answer...
• How to Determine Correct JT's Strong Arm Jack Stabilizer Kit for 5th Wheel Trailer
  We can help you determine the correct JT's Strong Arm Jack Stabilizer Kit for your Keystone Cougar 5th wheel trailer, though the kits aren't designed to fit any certain model, and we don't have a way of knowing the distance between your landing gear, which is the measurement needed in order to determine the right kit. So to determine the correct one what you need to do is simply measure the distance from inside-to-inside of your landing gear and you can get the right based on that number. -...
  view full answer...
  
• Length of Short Arms Included with Lippert JT's Strong Arm Jack Stabilizer # LC191024
  The shorter arms included in the Lippert Components JT's Strong Arm Jack Stabilizer # LC191024 measure 21-3/4 inches retracted and just about 43 inches when extended. This measurement is from the center of one hole to the center of the other. This kit will include four stabilizer tubes for the front of the coach and two for the rear. It will also include all of the hardware necessary for installation.
  view full answer...

Do you have a question about this Camper Jack?