Will Torklift Tie Downs from 2024 GMC Sierra 3500 Fit 2025

Question

Question:

Have a 2024 GMC 3500 with installed TL44PR torklift holddowns installed Changing to a 2025 GMC 3500 can I buy just the truck mounted hardware and not the loose alum brackets

asked by: Bob R

0

Expert Reply:

Hey Bob, so just the frame bracket portion of the tie downs is not available by itself and even if they were the removable portion by itself is not the same between trucks. So you would need a new set of Torklift tie downs but to pick that out I would need to know your bed length, if you have a dually or a single rear wheel axle, if you have running boards, and also if you have a factory hitch.

I attached a link to a page that has all of the tie down kits we offer as well.

expert reply by: Jameson C

0

Jameson C.

10/30/2025

Hey Bob, what did you end up finding for the new Torklift tie downs on your 2025 GMC 3500? Knowing which setup worked could really help others upgrading to the newer truck.

Answer 1

Hey Travis, the #LC736514-ELKIT requires 8.5 inches of clearance from the top bolt jack to the top of the motor for installation. If you only have 6.5 inches of clearance this would not work for you.

view full answer...

Answer 2

There is another solution, but unfortunately there is not a manual to electric conversion kit for the HappiJac 4160. You would need to upgrade your jacks to the HappiJac Electric Truck Camper Jack System #LC736514-ELKIT. The Manual-to-Electric…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...