Replacement Install Hardware for Curt Hitch # 13555

Question

Question:

I have a 13555 hitch for a 07 Honda CRV I just don’t have the bolts for installation. Could you help me with everything I need for installation? Measurements for bolts and everything required to instal. Thank you

asked by: Dylan

0

Expert Reply:

Hey Dylan, so we have the part # RHK which is a way to order replacement install hardware for all of the hitches we carry including the # 13555 that you referenced. Otherwise here is the size of the hardware that comes with it:

M10x1.25,30,CL10.9
U-BOLT,7/16-14 UNC,1-1/2

expert reply by: Jameson C

0

Jameson C.

1/5/2026

Hey Dylan, did the replacement hardware kit work out for your Curt hitch on the CR-V? Knowing how the fit turned out could help others trying to replace their missing bolts too.

Answer 1

The u-bolt included in the hardware for hitch #13555 is a 7/16 - 14 x 1.75" x 1.00" C-C u-bolt. We do not offer this item alone but you can probably find one locally using those specs. We do offer the complete replacement hardware kit for…

view full answer...

Answer 2

The Draw-Tite trailer hitch receiver, part #75547, uses 4 hex bolts that are M10 X 1.25 X 30. However, you shouldn't tap the threads uness you absolutely have to as a last resort. I highly recommend cleaning them before tapping them. I've…

view full answer...

Answer 3

The tap you want to use for installing the Curt Trailer Hitch Receiver #13555 on your 2011 Honda CR-V is 10x1.25mm as the bolts that come with the hitch are M10x1.25. Attached is an installation video of this hitch on a 2011 CR-V for you to check…

view full answer...

Answer 4

The u-bolt included with the Curt Trailer Hitch Receiver part #13555 is a 7/16-14x1-3/4"x1". We don't offer the u-bolt separately but you can replace it with the entire kit, Replacement Hardware Kit for Trailer Hitches part #RHK.

view full answer...

Answer 5

The bolts included with the Draw-Tite Class III #75471 Hitch are Class 10.9. They're 10mm in diameter, 30mm long and have a 1.25 thread pitch. If you're needing replacement installation hardware, we can supply a replacement hardware kit for…

view full answer...

Answer 6

If you will be cleaning up your current hitch and reinstalling it, you will require new hardware because they have already been torqued once. You can either replace the entire hitch (I've linked the page to your options) and use the hardware that…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Replacement Install Hardware for Curt Hitch # 13555

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching