Drill Tap Size for Installing Curt Hitch on 2011 Honda CR-V

Question

Question:

10 x 1.25 mm or 10 x 1.50 mm? I have two metric taps which are the same diameter, but different thread count. Which is needed for the #13555 Curt hitch - 2011 Honda CR-V?

asked by: David D

0

Expert Reply:

The tap you want to use for installing the Curt Trailer Hitch Receiver # 13555 on your 2011 Honda CR-V is 10x1.25mm as the bolts that come with the hitch are M10x1.25.

Attached is an installation video of this hitch on a 2011 CR-V for you to check out. If you let me know what you plan on using the hitch for I'd be more than happy to make a recommendation for you!

expert reply by: Jon G

0

Answer 1

Hey Dylan, so we have the part #RHK which is a way to order replacement install hardware for all of the hitches we carry including the #13555 that you referenced. Otherwise here is the size of the hardware that comes with it: M10x1.25,30,CL10.9…

view full answer...

Answer 2

The u-bolt included in the hardware for hitch #13555 is a 7/16 - 14 x 1.75" x 1.00" C-C u-bolt. We do not offer this item alone but you can probably find one locally using those specs. We do offer the complete replacement hardware kit for…

view full answer...

Answer 3

The Draw-Tite trailer hitch receiver, part #75547, uses 4 hex bolts that are M10 X 1.25 X 30. However, you shouldn't tap the threads uness you absolutely have to as a last resort. I highly recommend cleaning them before tapping them. I've…

view full answer...

Answer 4

The u-bolt included with the Curt Trailer Hitch Receiver part #13555 is a 7/16-14x1-3/4"x1". We don't offer the u-bolt separately but you can replace it with the entire kit, Replacement Hardware Kit for Trailer Hitches part #RHK.

view full answer...

Answer 5

If you will be cleaning up your current hitch and reinstalling it, you will require new hardware because they have already been torqued once. You can either replace the entire hitch (I've linked the page to your options) and use the hardware that…

view full answer...

Answer 6

The bolts included with the Draw-Tite Class III #75471 Hitch are Class 10.9. They're 10mm in diameter, 30mm long and have a 1.25 thread pitch. If you're needing replacement installation hardware, we can supply a replacement hardware kit for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Drill Tap Size for Installing Curt Hitch on 2011 Honda CR-V

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching