Replacement for MaxxAir Circuit Board 10B21276KZ

Question

Question:

What is the difference between circuit boards 10B21276KZ my board and 10A21276KZ your board

asked by: Marvin A

0

Expert Reply:

Hi Marvin; the Replacement Printed Circuit Board for MaxxAir Manual Lift RV Roof Vents # MA10A21276K won't be any different than your current 10B21276KZ and is the correct replacement. They have updated the model number over the years as they update fans. This is technically the 10C21276K now so it they have moved to C and replaced the A and B models that came before it.

expert reply by: Robin H

0

Robin H.

1/5/2026

Hey Marvin, how did things go with the replacement circuit board for your MaxxAir roof vent? Did the updated version work smoothly in place of your old one? Your feedback could help others sorting through the same model updates.

Marvin B.

1/5/2026

Hi robin, Yes, the circuit board worked great in our MaxxAir roof vent and I understand the fault in the design has been corrected so It will not short out again with moisture. The installation was easy if your a handy sort of person and it was a good opportunity to clean the blades and surrounding mechanisms completely. I was surprised, almost shocked, to find the motor was not brushless and that the brushes were worn down to the point of near failure already in less than 4 years of part time use. I turned the commutator and gave it some more life but assume the motor will need replacing in the near future. I will contact you when the time comes and hopefully we can come up with a brushless replacement. Thanks for your help with this project. Cheers Marvin

Answer 1

Welcome back Chris. The original MaxxFan 5100k fans couldn't handle the extra voltage from Lithium batteries and the boards would burn out. A green light would come on and beep after the fan runs for only a few seconds, which sounds like exactly…

view full answer...

Answer 2

Your MaxxFan Plus Roof Vent w/ 12V Fan and Thermostat - Manual Lift - 10 Speed - White #MA00-04000K could be cutting off after 10 seconds for the following reasons: 1. Insufficient or fluctuating power. Your fan could be receiving less than 12v of…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Replacement for MaxxAir Circuit Board 10B21276KZ

Product Page this Question was Asked From

Continue Researching