Recommended Hitch for a 2014 Acura TL
Updated 02/17/2026 | Published 06/13/2024
Products Featured in This Question
Question:
Hello my name is Marc, and Im messaging about choosing the right trailer for my vehicle. I own a 2014 Acura TL and Im taking the steps to tow a motorcycle, below 500 pounds. Between the Draw-Tite Class I and Curt Class I trailer hitch, which should i choose, is there even a difference?
asked by: Marc
Expert Reply:
Hey Marc! Between the Curt item # C11496 and the Draw-Tite item # 24899, I would go with the Draw-Tite Hitch item # 24899 because you see less of it after it's installed. Functionally, they both install in the same way and have the same capacities. The Draw-Tite is just tucked back in farther beneath your Acura.
Either way you go you will be limited to 1,000 lbs of towing capacity including your bike and trailer. Your 2014 Acura TL tops out at 1,000 lbs for towing capacity and you will want to go off of that number not the hitches capacities.
I have linked a couple of installation videos below along with the instructions so you can see how to get them set up.
Since you are planning on towing you will also need a wiring harness item # 46255 and the Draw-Tite Drawbar item # 3593 and then for hitch balls item # 19258 for a 2 inch ball or item # 19256 for a 1-7/8 inch ball.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- For Towing
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Q&A: Recommended Trailer Hitch Receiver and Wiring Harness For a 2014 Honda Accord Sedan EX-L
- Q&A: Replacement Trailer Hitch Hardware Needed For A 2012 Acura TSX
- Shop: Vehicle Tow Bar Wiring
- Search Results: draw bars
- Search Results: trailer wiring
- Shop: 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Chrome - 10,000
- Shop: 2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Malone Anti-Rattle HitchLock System
- Search Results: hitch extender
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: trailer tires and wheels
- Shop: Suspension Enhancement
- Video: Curt Powered Tail Light Converter Installation - 2023 Kia Telluride
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Video: Clean Up Your Trailer Wiring
- Search Results: trailer hitch ball mount
on Trailer Hitch
Jerred H.
2/17/2026
Hey Marc, how did things go with the Draw-Tite hitch on your Acura TL? Did it give you the clean look and towing setup you were hoping for with your motorcycle trailer? Your update could make it easier for others choosing between those two hitches.