Are Replacement Spring Bars Available For The Curt TruTrack 4P Weight Distribution System # C74RV

Question

Question:

2005 Ford Excursion, towing a 3500-4500 lb single axle travel trailer with a tongue weight of 350-500 lb . I like the quick disconnect feature of this Curt 17520 WD hitch. Will the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System - 800 lbs TW,Item C17535 fit the Curt 17520?

asked by: Paul

0

Expert Reply:

Hey Paul,

I spoke with Curt and they stated that the Replacement Trunnion Spring Bar for Curt TruTrack Weight Distribution System # C17535 would only be compatible with the # C17499. The Curt TruTrack 4P Trailer Mounted Weight Distribution System w/ Sway Control # C74RV (17520) is such a new part that Curt doesn't have replacement parts set up for it yet but is working on it.

That being said neither of these would properly distribute the weight and would instead make it worse because they're too highly rated for 350-500lbs of tongue weight. Instead I recommend the Blue Ox SwayPro Weight Distribution w/ Sway Control # BXW0550. I've used this system numerous times and love how easy it is to install and use. The spring bars are interchangeable with this head so you'll be able to upgrade later on if you need to tow a heavier trailer.

expert reply by: Kevin C

0

Doug S.

7/3/2024

I just bought a new Intech Sol Dusk Rover which has a GVWR of 4800 lbs, with a TW of 540-575 lbs. I’m pulling this with a 2020 Jeep Grand Cherokee Limited X (5.7L Hemi) rated for 6,000 lbs, carrying approximately 300 lbs cargo behind the rear axle. The truck accessory store I ordered my trailer brake kit and WD hitch recommended the Curt 17499 WD hitch with sway control, which is rated from 6,000-8,000 lbs. Seems like overkill but what would you recommend?

Kevin C.

7/3/2024

@DougS The current consensus from weight distribution hitch manufacturers is that the payload (300lbs) inside your Grand Cherokee would not count towards the spring bar capacity range of the weight distribution hitch but would towards to the tongue weight capacity of the trailer hitch receiver on your vehicle. The Curt TruTrack Weight Distribution System # C17499 has a tongue weight range of 500 - 800lbs so it would fall within your estimated trailer tongue weight, but it would likely be overkill. The only way to really know would be to fill the trailer like you were going to go camping and then measure the tongue weight with a scale. If you end up a little lighter and sit in the 400lb - 600lb range then you could go with something like the Fastway e2 Weight Distribution w/ 2-Point Sway Control # FA94-00-0600 instead.

Answer 1

The Curt TruTrack Weight Distribution System part #C17500 which is rated for up to 10,000 lbs gross trailer weight and 1,000 lbs tongue weight would work but it wouldn't perform as well as the Curt TruTrack Weight Distribution System part #C17499…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Thanks for supporting a local business Christopher! So long as your 2012 Chevrolet Silverado is a 1500 and you need a class IV hitch, the Curt item #14301 is going to be the best option. It has a 2" receiver with a 10,000 lbs towing capacity and…

view full answer...

Answer 11

Hey Frank. I can give you the dimensions of the shank on the B&W Continuum item #BW28FR but you're going to need to take the measurements on your Silverado 3500 to confirm the tailgate will open. From the hitch pin hole to the center of the…

view full answer...

Answer 12

For a hitch with a shorter distance between the mounting flanges down to the hitch opening that is confirmed to fit your 2014 Chevy Silverado you would want the B and W hitch #BWHDRH25601 over the Curt Hitch part #C15800. This hitch has slightly…

view full answer...

Are Replacement Spring Bars Available For The Curt TruTrack 4P Weight Distribution System # C74RV

Products Featured in This Question

Continue Researching