Best Place for Running Wiring For a Trailer Brake Controller Into Cab on a 2022 Subaru Outback
Products Featured in This Question
Question:
2022 Outback Wilderness: Im looking for clarification on passing the wires thru the firewall. There is a big round grommet in the engine bay that looks easy enough to puncture. But on the inside it is not so clear. Would I need to cut a slit in the long black rubber tube on the inside? Would it be best to send my fish from the slot on the inside to see where it pokes through the engine grommet? Just making sure this is the best place to not damage anything. Thanks! My proposed cut location marked in Red on the photos
asked by: Todd S
(click to enlarge)
Expert Reply:
I always recommend being careful when cutting into any grommets as you do not know what may be inside or behind them. I do see that in our Installation video for the Tekonsha P3 Trailer Brake Controller # 90195 they used the same hole to pass the wires through for. I have linked this video near the bottom of the page and you can see the location near the 13:00 mark of the video. There he only slits an opening in the grommet itself and not the rubber tube. As I see you are looking at the Redarc Liberty # RED24FR you will need the Pigtail # RED69FR. If you do not already have trailer wiring we have the 4-Way # C56040 and 7-Way # ETBC7 you would need.
Todd S.
3/14/2024
Thanks Bud, Success! I got the wires thru the firewall. Can you help me confirm the cold brake sensor wire size and color (that attaches to the redarc controller)? The video on redarc page says brown wire. I do no have a brown wire. Other later model subaru owners are saying it is Yellow. It is also very small and hoping to confirm the size before installing the wrong quick connect. Thanks for your help!
Product Page this Question was Asked From
Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Plug-In
- Dash-Mounted Knob
- Behind-Dash
- Up to 2 Axles
- Indicator Lights
- Single Trailer Only
- Redarc
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Video: Installation Guide for the Curt Trailer Hitch Receiver on a 2024 Subaru Outback Wagon
- Shop: etrailer Towing Kit w/ 2" Ball Mount and Pre-Torqued 2-5/16" Ball - 2" Drop - 7.5K
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Search Results: fishing rod holders
- Search Results: 4 pin
- Search Results: 4 pin holder
- Q&A: Can 2024 Subaru Outback Wagon Curt T-Connector 4-Way Be Ran Under the Vehicle
- Video: Brophy Mounting Bracket for 4-Pole Flat Trailer Connector: The Breakdown
- Video: Curt T-Connector Vehicle Wiring Harness Installation - 2024 Subaru Outback Wagon
- Video: An In-Depth Look at the Curt Easy Mount Bracket for 4- or 5-Way Flat Trailer Connector
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat Trailer Connector - 2" Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Mounting Bracket 4-Pole Flat
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Brophy Mounting Bracket for 4-Pole Flat Trailer Connector
- Shop: Bauer Products 4-Way Trailer Plug Holder
- Q&A: Parts Needed To Connect Lights From A Removable Trailer Extension To A 5th Wheel
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Finding the Right Trailer Wiring Harness
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer wiring
- Article: Trailer Wiring Diagrams
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch ball mount
- Q&A: Difference Between Curt and etrailer Trailer Hitch Receivers for 2020 Chevy Colorado
- Video: How to Install: Draw-Tite Max-Frame Trailer Hitch Receiver on your 2024 Subaru Outback Wagon
- Shop: Brake Controller
- Article: How to Choose the Right Trailer Hitch Class
on Trailer Brake Controller
Todd S.
3/14/2024
Hi Bud, More specifically can you find out if the photo on the inside of the car is the correct place (other side of engine wall) and that the wires would come through the rubber loom? Check out the videos for the RED24FR for the subarus, they mention cutting a slit on the inside of the car but never show it in the video, so I'm wondering if I have the right spot. Maybe I should send a fish from the engine side and see if I can see it trying to poke through on the inside? Thanks