Install Instructions for the Progressive Dynamics 9100 Converter
Updated 01/08/2024 | Published 01/05/2024
Question:
I just purchased a PD9130lv converter/ charger from etrailer.com and I have been researching how to install it to replace the current Magnetex 6332. My question concerns the blue wire labelled converter outputinch on the Magnetex conv. which is connected to the dc distribution panel along with the red and white wires to the battery. I see where the red and white wires connect to the PD9130lv but not sure where to connect the blue wire. Thank you. Peace, I have a 2000, 24 ft. Winnebago RV on a Ford 350 Super Duty chassis.
asked by: Ron E
Expert Reply:
I went ahead and looked up the instructions for the Progressive Dynamics 9100 Inteli-Power Lithium Converter # PD4645V and was able to find some more info for you. For the install instructions, you'll need to:
1. Secure converter firmly to mounting surface.
2. Connect chassis ground lug (found on unit base)
to chassis.
• Ground wire to be between 6 and 12AWG
wire.
3. Disconnect battery from both positive (+) and
ground (-) cables.
4. Connect battery ground (-) to converter NEG (-)
lug.
• Conductor to be between 2 and 14AWG
(follow all applicable codes when sizing
conductor).
5. Disconnect any optional pendants or modules.
6. Plug converter into appropriate outlet.
7. Using a DC voltmeter, verify converter output.
8. Disconnect power to converter.
9. Connect battery positive (+) to converter POS (+)
lug.
• Conductor to be between 2 and 14AWG
(follow all applicable codes when sizing
conductor).
Note: When connecting battery to converter
POS (+), a spark may occur. This is normal.
10. Reconnect cables.
11. Reconnect any optional pendants or modules.
12. Reconnect power to converter.
I have also included a diagram to go with these directions for you to check out as well.
(click to enlarge)
Product Page this Question was Asked From
Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel - 45 Amp
- Accessories and Parts
- Power Converter
- Converter Section
- 45 Amp
- Progressive Dynamics
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: progressive dynamics
- Shop: Progressive Dynamics 9300 Series RV Converter Charger - 12V - 60A
- Search Results: 6 way connector
- Search Results: hm40975~11998
- Search Results: circuit tester
- Q&A: Replacing 6-Way on Trailer With 7-Way Connector
- Video: Review of Progressive Dynamics RV Power Converter - Standard Charge - PD69RR
- Video: Review of Progressive Dynamics RV Power Converter - Standard Charge - PD79RR
- Shop: Progressive Dynamics 9300 Series RV Converter Charger - 12V - 45A
- Shop: Trailer Wiring
- Article: Wiring Trailer Lights with a 6-Way Plug (It's Easier Than You Think)
- Shop: Curt Trailer Connector Adapter - 4-Way to 7-Way RV and 4-Way Flat
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: How to Tell if Trailer Has 6-Way or 7-Way Installed
- Shop: Threaded Hitch Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device - 4-1/2"
- Shop: Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel - 45 Amp
- Shop: Replacement Section for AC/DC Power Distribution Panel - 35 Amp
- Q&A: Can Internal Parts Be Replaced for 45 Amp Progressive Dynamics Replacement Section
- Q&A: Recommended Replacement for a Magnetek Model 6325 Converter
- Q&A: Replacement Converter for Parallax 7345A
- Q&A: Replacement Power Converter for Magnetek Power Converter 6300/6332
- Article: Trailer Wiring Diagrams
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Hitch
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Search Results: trailer wiring
on Accessories and Parts
