Does the Curt Hitch C15398 Support the Bumper on a 2013 Toyota Tundra?
Published 12/03/2023 >
Question:
You have responded that the C15398 will work on a 2023 Tundra SR 5 with a factory installed hitch. A video showing the installation of this hitch shows no support for the bumper. Is there anything to support the bumper to the C15398 hitch. The factory provided hitch has the bumper bolted with a single bolt to the hitch at the lower center point of the bumper. Is it necessary to support the middle of the bumper?
asked by: Anthony T
Expert Reply:
That is correct. There is nothing to support the bumper when you install the Curt Hitch item # C15398 on a 2013 Toyota Tundra. That hitch was designed for the trucks without the factory hitch so there's no reason for it to have built in support for the bumper. It'll work on the Tundra's that came with a factory hitch so long as you get everything out of the way including the factory hitch's bumper support.
It is not necessary to support the bumper with an aftermarket hitch like the Curt item # C15398.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- For Towing
- Class V
- 2400 lbs TW
- 16000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Q&A: Will the Curt Class V Trailer Hitch Fit on a 2010 Toyota Tundra TRD
- Video: Mount: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Q&A: Is there a Hitch for the 2013 Toyota Tundra's that Have a Factory Hitch?
- Q&A: Aftermarket Hitch for 2012 Toyota Tundra Rock Warrior TRD with Damaged Factory-Installed Hitch
- Q&A: Trailer Hitch For A 2011 Toyota Tundra
- Q&A: Can An Aftermarket Trailer Hitch Be Installed On a 2007 Toyota Tundra If Bumper Is Replaced
- Q&A: Can Curt Trailer Hitch Receiver be Installed on a 2011 Toyota Tundra After Factory Hitch is Removed
- Q&A: Replacement Hitch for 2020 Toyota Tundra With Factory Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Wiring
- Shop: Mud Flaps
- Video: Installation: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Search Results: mud flaps
- Shop: Lionshead Trailer Wheel Center Cap w/ Snap-In Plug - 3.19" Pilot - Stainless Steel
- Shop: WeatherTech Mud Flaps - Easy-Install, No-Drill, Digital Fit - Front and Rear Set
- Shop: Dexter Self-Contained Hydraulic Jack - Square Tube - 20" Lift - 10,000 lbs - Bolt On
- Shop: Dexter Double-Acting Hydraulic Trailer Jack System - 20" Lift - 10,000 lbs - Direct Weld
- Search Results: electric jack
- Search Results: electric jack gooseneck
- Search Results: loctite
- Shop: Loctite Blue Stick Threadlocker - Medium Strength - 1/4" - 3/4" Nuts/Bolts - 0.67-Oz Stick
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer wiring
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector

