Replacement Hitch for 2020 Toyota Tundra With Factory Hitch
Updated 05/30/2024 | Published 05/25/2024 >
Question:
I have a 2020 Toyota Tundra Crewmax Platium with tow package. The hitch was already installed but previous owner used it for boating and it is Rusty. Our toyota service guy says it is too rusted and not safe to tow. We need to replace the assembly and your product looks like it might work. Your opinion?
asked by: Margaret S
Expert Reply:
Hi Margaret; it is possible to replace your 2020 Tundra factory hitch with the Curt # C15398. The one thing to keep in mind is that installation will require removing the old hitch which is part of the support for the rear bumper. Curt is unable to confirm how secure the bumper is once the old hitch is removed. Aside from a factory replacement this is the only option available.
I would reach back out to your service guy and check to see if it is possible to pull bumper supports or a full bumper off an old Tundra that did not have the factory hitch and replace yours. This has been a solution for other vehicles with the same issue from an integrated factory hitch. If isn't possible it would be something you have to live with if you want to add an aftermarket hitch.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- For Towing
- Class V
- 2400 lbs TW
- 16000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Video: Mount: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Q&A: Does the Curt Hitch C15398 Support the Bumper on a 2013 Toyota Tundra?
- Q&A: Fit Confirmation for Curt Hitch C15398 on 2007 Toyota Tundra
- Q&A: Is there a Hitch for the 2013 Toyota Tundra's that Have a Factory Hitch?
- Q&A: Will the Curt Class V Trailer Hitch Fit on a 2010 Toyota Tundra TRD
- Q&A: Can An Aftermarket Trailer Hitch Be Installed On a 2007 Toyota Tundra If Bumper Is Replaced
- Q&A: Can Curt Trailer Hitch Receiver be Installed on a 2011 Toyota Tundra After Factory Hitch is Removed
- Q&A: Will the Curt Trailer Hitch Receiver Fit a 2007 Toyota Tundra with Factory Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Shop: Suspension Enhancement
- Article: How to Measure for Trailer Hitch Drop
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Search Results: trailer tires and wheels
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers
- Search Results: trailer jack
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Brake Controller
- Shop: Gooseneck Hitch
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)


