Can An Aftermarket Trailer Hitch Be Installed On a 2007 Toyota Tundra If Bumper Is Replaced
Updated 05/18/2024 | Published 06/21/2020 >
Question:
I have done a lot of salt water boat-launching with my 2007 Tundra and my rear bumper and factory hitch need to be replaced. Toyota recently put a brand new frame in my truck due to a frame defect, so it should be possible to get some more good years out of the truck. Many of the class 5 hitches you carry state they won’t fit trucks with “factory installed hitches”. Am I correct to assume this is because one would have to also replace the bumper? Since my intention is to buy a cheaper after market bumper anyhow Will I be able to use one of these class 5 hitches? Thanks!
asked by: Rich H
Expert Reply:
The factory trailer hitch options for a 2007 Toyota Tundra are tied into the rear bumper helping to provide extra support. This is why the factory trailer hitch cannot be replaced with an aftermarket trailer hitch as these do not tie into the bumper. However, if you were to remove the factory bumper in light of any aftermarket bumper you could then install an aftermarket hitch like the Curt Trailer Hitch Receiver part # C15398.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- For Towing
- Class V
- 2400 lbs TW
- 16000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Trailer Wiring
- Shop: Nerf Bars - Running Boards
- Search Results: 86~00~5015
- Search Results: scissor
- Shop: Atlas IV Vaquero Self-Contained Hydraulic Trailer Jack - Bolt On - 10K
- Search Results: kayak trailer
- Search Results: gnrk1067
- Search Results: kayak rack
- Shop: etrailer Scissor Stabilizer Jacks w/ Handle and Drill Adapter - 24" Lift - 5,000 lbs - Qty 2
- Shop: etrailer Scissor Stabilizer Jack - 24" Lift - 2,500 lbs - Qty 1
- Search Results: safe~t~alert
- Search Results: 090~011~02
- Video: Review of Stillwell Trailer Jack - Single-Acting Hydraulic Trailer Jack - ST55FR
- Q&A: Will the Curt Class V Trailer Hitch Fit on a 2010 Toyota Tundra TRD
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Scissor Stabilizer Jacks w/ Handle - 18-3/4" Lift - 10,000 lbs - Qty 4
- Shop: Kenda Loadstar 205/65-10 Bias Trailer Tire w/ 10" Solid Center Wheel - 5 on 5-1/2 - LR E
- Shop: Gooseneck Hitch
- Shop: Roof Rack
- Q&A: 2025 Chevy Colorado Trailer Hitch and Brake Controller Recommendations
- Video: Review of Dexter Trailer Jack - Self-Contained Hydraulic Jack - DX72CR
- Q&A: Can an Aftermarket Trailer Hitch be Installed on a 2017 Toyota Tundra with Factory Trailer Hitch
- Q&A: Trailer Hitch For A 2011 Toyota Tundra
- Q&A: Aftermarket Hitch for 2012 Toyota Tundra Rock Warrior TRD with Damaged Factory-Installed Hitch
- Q&A: Is there a Hitch for the 2013 Toyota Tundra's that Have a Factory Hitch?
- Q&A: Does the Curt Hitch C15398 Support the Bumper on a 2013 Toyota Tundra?
- Video: Mount: Curt Trailer Hitch Receiver on a 2013 Toyota Tundra
- Shop: Brake Controller


Todd
5/18/2024
But do you sell the adapter part to reconnect the bumper to the hitch? Looks like I could have something fabricated but could be expensive.