Recommended Tonneau Cover For A 2018 Ford F-150 With A 20" Toolbox

Question

Question:

I have a 2018 ford f150 65inch bed with a 20inch tool box do you have a compatible Tonneau cover to fit my truck?

asked by: Bryant N

0

Expert Reply:

Yes, we have one fit with the Access Toolbox Edition Soft, Roll-Up Tonneau Cover # A61369, which works with over-the-rail toolboxes that are 19" - 21". I've attached a short video below where Adam will give you a walk through of how this cover works.

expert reply by: Kevin C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Hey Gregory, that's really good information. You’ve got a few options, but I wouldn’t jump straight to replacing the leaf springs on a half-ton for that size trailer. Since you’re using a Curt weight distribution hitch, that should be doing most…

view full answer...

Answer 8

Hey Don, thanks for the information! That's a significant amount of sag and a pretty heavy trailer, I recommend the Hellwig Pro Series Helper Springs item #HE79FR for the higher 2,500 lbs capacity. I doubt you're driving around with your bed…

view full answer...

Answer 9

Hey Douglas, whenever available I recommend going with the HD version of the Roadactive kits like the part #RAS3611-YHD that fits your 2022 Ford F-150 4WD. The extra capacity of this kit over the non-HD basically doesn't have any downside aside…

view full answer...

Answer 10

Hey Dennis! I can't say if it will clear for sure but I can give you dimensions to help determine if it will. Using the furthest hitch pin hole, the Malone 2" Dual Purpose Hitch Receiver #MPG544 will push the bike rack out 12-1/4". When…

view full answer...

Answer 11

Hey Joe. To charge your F-150's battery while flat towing, you'll need to add a battery charge line kit item #RM-156-25. It's going to connect directly to your truck's battery and has a 15 amp circuit breaker included. You'll wire…

view full answer...

Answer 12

Hi Bruce! The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A63FR will indeed fit your 2021 GMC Serra 1500 SLT with the short bed and your toolbox. This can be used with toolboxes that measure 19" to 21" long, so you are good to go!…

view full answer...

Recommended Tonneau Cover For A 2018 Ford F-150 With A 20" Toolbox

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching