What Size Bolts Are Used For Curt Hitch Installation For Thread Tap/Chaser on 2011 Highlander

Question

Question:

Im putting this on a 2011 Highlander and would like to run a tap through the holes on the frame, but I cant seem to find out what size tap I would need. Can anyone help me?

asked by: Shawn

0

Expert Reply:

The Curt # 13534 uses M10x1.25 bolts so you will need a tap that matches. You could also use a thread chaser to clean out the existing threads rather than cut new ones.

expert reply by: Robin H

0

Answer 1

Hey Pamela, thanks for the picture and congrats on your new trailer. The Curt True Course item #C94VV has inertia sensors in it. You'll want to bolt it to the side of your coupler beneath that metal storage box for it to function correctly. Being…

view full answer...

Answer 2

Hi Jim, Since you can't use a weight distribution hitch and don't want to drill through the aluminum frame I recommend attaching the Curt True Course Advanced Bluetooth Trailer Sway Control #C94VV to a board and using some U-bolts to clamp…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Aaron, great question! The Trailer Mate Trailer Hitch Receiver #TMT67FR is definitely a budget friendly option for a hitch on your 2026 Highlander. This is basically the economy line from Curt. The welds are a little different (but will still do…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Size Bolts Are Used For Curt Hitch Installation For Thread Tap/Chaser on 2011 Highlander

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching