Can the Replacement Drive Head Motor Gear Pack for Solera Power RV Awnings Be Delivered to Canada

Question

Question:

I am located in Quebec, Canada. Would need part Replacement Drive Head Motor Gear Pack for Solera Power RV Awnings Item # LC78VR. Do you mail to Canada or do you have a place where your parts are available in Quebec City. Canada

asked by: Joanne C

0

Expert Reply:

Yes, we do deliver to Canada!

Just place the order for the Replacement Drive Head Motor Gear Pack for Solera Power RV Awnings # LC78VR and enter your shipping information in at checkout.

expert reply by: Scott S

0

Answer 1

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 2

Hey Mark, the oscillating vent of the Furrion Chill Cube #FR27TD points to the front. Is there anyway you could use it pointing forward?

view full answer...

Answer 3

The roof vent on your trailer is most likely for black water tank. The Lippert Components 360 Siphon RV Holding Tank Vent Cap part #LC389381 has a base with a 4" outer diameter. The holes most likely won't line up with your existing roof…

view full answer...

Answer 4

Yes, we do Stephanie! It is the Specialty Recreation Low Profile Skylight w/ Inner Garnish and Sealant item #SR56RR. It measures 17-1/2" wide x 25-1/2" long and the bubble height is 4". It will fit over a standard 14" wide x…

view full answer...

Answer 5

Hello Mark. Great question. I am all about fixing what you have, however with part of it being delaminated you might want to take a closer look just to make sure that there is not severe water damage underneath. If the roof membrane is still in great…

view full answer...

Answer 6

If you are referring to the head pin then yes we do have this available as the Replacement Head Pin for Solera Power Awning Gear Drive Head part #LC266141. That said, you would also want two Replacement Retaining Clips part #LC266137 and one…

view full answer...

Answer 7

I spoke with Lippert, and they informed me that for your Lippert awning you are going to need the: -Replacement Gear Pack for Lippert Solera Awning Motor #LC78VR, with the Replacement Head Pin for Solera Power Awning Gear Drive Head #LC93FR.

view full answer...

Answer 8

To remove the old pin you'll need to remove the cover, remove the two retaining pins, and then slide the old pin out. To install the #LC93FR you'd just reverse the process.

view full answer...

Answer 9

Not quite, there is an additional screw below the wax screw in the end cap that also must be removed on the Solera Power Awning Idler Head #LC672052. From here you can remove the roll tube from the drive head. After the drive head is removed, there…

view full answer...

Answer 10

Since you were looking at the Regal style idler head #LC672052 I'm assuming you need to replace the idler head pin on your Solera awning. You can remove the old pin and install #LC27WD for a replacement. If by key you mean a cotter pin, then yes…

view full answer...

Answer 11

The Replacement Drive Head Motor Gear Pack #LC78VR does not have another option. Lippert only makes the one gear pack. With you going through 2 of these in 2 years it makes me think there is something wrong with your awning installation. If there is…

view full answer...

Answer 12

Yes the gear pack part #LC78VR does work with both the motor kits you mentioned of #LC266149 and #LC373566.

view full answer...

Can the Replacement Drive Head Motor Gear Pack for Solera Power RV Awnings Be Delivered to Canada

Product Page this Question was Asked From

Continue Researching