Will etrailer Scissor Jacks Fit 2014 Premiere Bullet BHS

Question

Question:

Will this Jack work with my 2014 30ft premiere Bullet bhs

asked by: Stacie C

0

Expert Reply:

Yes, the Scissor Jacks part # TJSCHD-24-4 would work on your 2014 Premiere Bullet BHS due to it's universal design.

expert reply by: Jameson C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Hey Edgar, I've attached a diagram below that should have all the measurements you need for the mounting brackets of the etrailer Scissor Stabilizer Jacks w/ Handle #TJSCHD-24-4. The brackets are about an 1/8" thick.

view full answer...

Answer 7

Hi Rob, The Taskmaster Trailer Wheel Lug Nut part #TA66QR requires a 3/4" socket for installation. However, we do have the CE Smith Trailer Wheel Acorn Lug Nut part #CE16720 that is 1/2"-20 with a chrome plate finish and works with a…

view full answer...

Answer 8

Hey Ryan, I would recommend the Fastway e2 weight distribution system part #FA92-00-0800 for your 2026 Forrest River Cherokee Wolf Pup 16BHSW as it has a 400-800 lb tongue weight rating which would be correct for your setup and also because Fastway…

view full answer...

Answer 9

Hey John, while we have something that'll work for you, we don't have Strong Arm stabilizer kits for just the 2 rear jacks; only 4 jacks. You could opt to replace the scissor jacks with Ark Drop Down Corner RV Stabilizer Jacks - 30" Long…

view full answer...

Answer 10

The wax screw you're referring to I believe is a #8 - 32 x 1/2”.

view full answer...

Answer 11

We do have a direct replacement for your Kwikee Steps 1800709 controller - this is found as the Replacement Control Unit for Kwikee 38 Series Electric RV Steps #LC363989 on our site. Our part numbers may differ from the manufacturers but I've…

view full answer...

Answer 12

Hi Steve, great question! The bolt spread dimensions on scissor jacks aren’t universal, they can vary a bit depending on the brand and capacity. Most standard RV scissor jacks use a mounting plate that’s roughly 3-1/4" wide with bolt holes…

view full answer...

Will etrailer Scissor Jacks Fit 2014 Premiere Bullet BHS

Product Page this Question was Asked From

Continue Researching